MCU packages

RP2350B pinout

QFN-80 · RP2350 · Release 8

Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe

At a glance

Platform / manufacturer
Raspberry Pi
Type
MCU packages
MCU
RP2350B
Package / connector
QFN-80
Physical contacts
80
GPIO
48
I/O voltage
1.8–3.3 V I/O
Interfaces (pin count)
I²C (56) · SPI (48) · UART (56) · USB (48) · ADC (8) · PWM (48) · CLOCK (15) · HSTX (8) · PIO (48) · QMI (10) · SIO (56)
Silicon introduction
2024-08-08 [b]
MCU / processor core
2 × Arm Cortex-M33 / 2 × Hazard3 RISC-V [a]
Clock speed / maximum
150 MHz [a]
Internal RAM / system RAM
520 KB SRAM [a]
Program Flash / storage
No internal Flash; external QSPI Flash required. [a]
Fixed ROM / boot ROM
32 KB boot ROM [a]
Power and logic level
Connect every supply, ground and exposed pad per datasheet; no board regulator is included. [a]
Pin sources checked
2026-11-15
Technical details reviewed
2026-11-14

Cautions for this board

All pins (80)

RP2350B: every pin in physical order with its type, functions and warnings
PhysicalPin nameTypeFunctionsNotes and warningsSource
01GPIO4General-purpose I/OSPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA2 F9USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
02GPIO5General-purpose I/OSPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA3 F9USB VBUS EN F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
03GPIO6General-purpose I/OSPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
04GPIO7General-purpose I/OSPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
05IOVDDPower——[4]
06GPIO8General-purpose I/OSPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS EN F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
07GPIO9General-purpose I/OSPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
08GPIO10General-purpose I/OSPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
09GPIO11General-purpose I/OSPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
10DVDDPower——[5]
11GPIO12General-purpose I/OHSTX F0SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
12GPIO13General-purpose I/OHSTX F0SPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
13GPIO14General-purpose I/OHSTX F0SPI1 SCK F1UART0 CTS F2I2C1 SDA F3PWM7 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS EN F10UART0 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
14GPIO15General-purpose I/OHSTX F0SPI1 TX F1UART0 RTS F2I2C1 SCL F3PWM7 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB OVCUR DET F10UART0 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
15IOVDDPower——[4]
16GPIO16General-purpose I/OHSTX F0SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
17GPIO17General-purpose I/OHSTX F0SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
18GPIO18General-purpose I/OHSTX F0SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART0 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
19GPIO19General-purpose I/OHSTX F0SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS DET F10UART0 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
20GPIO20General-purpose I/OSPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB VBUS EN F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
21GPIO21General-purpose I/OSPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
22GPIO22General-purpose I/OSPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS DET F10UART1 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
23GPIO23General-purpose I/OSPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB VBUS EN F10UART1 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
24IOVDDPower——[4]
25GPIO24General-purpose I/OSPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT2 F9USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
26GPIO25General-purpose I/OSPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT3 F9USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
27GPIO26General-purpose I/OSPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
28GPIO27General-purpose I/OSPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
29IOVDDPower——[4]
30XINSystem——[5]
31XOUTSystem——[5]
32DVDDPower——[5]
33SWCLKSystem——[5]
34SWDIOSystem——[5]
35RUNSystem——[5]
36GPIO28General-purpose I/OSPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
37GPIO29General-purpose I/OSPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
38GPIO30General-purpose I/OSPI1 SCK F1UART0 CTS F2I2C1 SDA F3PWM7 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART0 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
39GPIO31General-purpose I/OSPI1 TX F1UART0 RTS F2I2C1 SCL F3PWM7 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART0 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
40GPIO32General-purpose I/OSPI0 RX F1UART0 TX F2I2C0 SDA F3PWM8 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
41IOVDDPower——[4]
42GPIO33General-purpose I/OSPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM8 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
43GPIO34General-purpose I/OSPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM9 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART0 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
44GPIO35General-purpose I/OSPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM9 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART0 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
45GPIO36General-purpose I/OSPI0 RX F1UART1 TX F2I2C0 SDA F3PWM10 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
46GPIO37General-purpose I/OSPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM10 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
47GPIO38General-purpose I/OSPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM11 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
48GPIO39General-purpose I/OSPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM11 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
49GPIO40_ADC0General-purpose I/OSPI1 RX F1UART1 TX F2I2C0 SDA F3PWM8 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10ADC0

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
50IOVDDPower——[4]
51DVDDPower——[5]
52GPIO41_ADC1General-purpose I/OSPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM8 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10ADC1

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
53GPIO42_ADC2General-purpose I/OSPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM9 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 TX F11ADC2

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
54GPIO43_ADC3General-purpose I/OSPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM9 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 RX F11ADC3

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
55GPIO44_ADC4General-purpose I/OSPI1 RX F1UART0 TX F2I2C0 SDA F3PWM10 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10ADC4

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
56GPIO45_ADC5General-purpose I/OSPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM10 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10ADC5

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
57GPIO46_ADC6General-purpose I/OSPI1 SCK F1UART0 CTS F2I2C1 SDA F3PWM11 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART0 TX F11ADC6

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
58GPIO47_ADC7General-purpose I/OSPI1 TX F1UART0 RTS F2I2C1 SCL F3PWM11 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS EN F10UART0 RX F11ADC7

Non-FT ADC/GPIO

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[6] [3] [1]
59ADC_AVDDPower——[5]
60IOVDDPower——[4]
61VREG_AVDDPower——[5]
62VREG_PGNDGround——[5]
63VREG_LXSystem——[5]
64VREG_VINPower——[5]
65VREG_FBSystem——[7]
66USB_DMSystemUART1 RX F2I2C0 SCL F3SIO F5—[5]
67USB_DPSystemUART1 TX F2I2C0 SDA F3SIO F5—[5]
68USB_OTP_VDDPower——[5]
69QSPI_IOVDDPower——[5]
70QSPI_SD3SystemQMI SD3 F0UART0 RTS F2I2C1 SCL F3SIO F5UART0 RX F11—[6]
71QSPI_SCLKSystemQMI SCK F0UART1 CTS F2I2C1 SDA F3SIO F5UART1 TX F11—[6]
72QSPI_SD0SystemQMI SD0 F0UART0 TX F2I2C0 SDA F3SIO F5—[6]
73QSPI_SD2SystemQMI SD2 F0UART0 CTS F2I2C1 SDA F3SIO F5UART0 TX F11—[6]
74QSPI_SD1SystemQMI SD1 F0UART0 RX F2I2C0 SCL F3SIO F5—[6]
75QSPI_SSSystemQMI CS0n F0UART1 RTS F2I2C1 SCL F3SIO F5UART1 RX F11—[6]
76IOVDDPower——[4]
77GPIO0General-purpose I/OSPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB OVCUR DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
78GPIO1General-purpose I/OSPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACECLK F9USB VBUS DET F10

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
79GPIO2General-purpose I/OSPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA0 F9USB VBUS EN F10UART0 TX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]
80GPIO3General-purpose I/OSPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA1 F9USB OVCUR DET F10UART0 RX F11

Conditional 5.5V input

RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]

[2] [3] [1]

Model-specific features and connection notes

Sources

Pin and warning references

  1. RP2350 Datasheet · PDF p. 1359Appendix D.5.1 · RP2350-E9 · increased leakage on Bank 0 GPIO inputs (A2 stepping; pp. 1359–1360)
  2. RP2350 Datasheet · PDF p. 1333§14.8.2.2 · Tables 1674–1679 · package pin list
  3. RP2350 Datasheet · PDF p. 1332§14.8.2.1 · Table 1673 · FT input conditions; pin types in Tables 1674–1679
  4. RP2350 Datasheet · PDF p. 17§1.2.1 · Figure 3 · IOVDD pads (Table 1679 discrepancy reviewed)
  5. RP2350 Datasheet · PDF p. 1335§14.8.2.2 · Tables 1674–1679 · package pin list
  6. RP2350 Datasheet · PDF p. 1334§14.8.2.2 · Tables 1674–1679 · package pin list
  7. RP2350 Datasheet · PDF p. 1336§14.8.2.2 · Tables 1674–1679 · package pin list

Technical sources (2)

  1. RP2350 DatasheetManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
  2. pico2 launch announcementRaspberry Pi · Publication date / product announcement

Locked source documents

Pin reference · Datasheet