Development boards
Raspberry Pi 500 pinout
Rear 40-pin GPIO header · RP1 alternate functions
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
Horizontal 40-pin GPIO header on the rear of the keyboard computer. Pin numbers follow the standard layout; this map shows the numbering, not the rear-panel view. Alternate functions come from the same RP1 table as Pi 5.
At a glance
- Platform / manufacturer
- Raspberry Pi
- Type
- Development boards
- MCU
- BCM2712 / RP1
- Physical contacts
- 40
- GPIO
- 28 (2 reserved)
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (18) · SPI (26) · UART (18) · PWM (6) · CLOCK (6) · DPI (28) · I2S (10) · PCM (5) · PIO (28) · SDIO (6) · SYSTEM (28)
- Initial sale / release date
- 2024-12-09 [d]
- MCU / processor core
- 4 × Arm Cortex-A76 (64-bit); RP1 I/O [a]
- Clock speed / maximum
- 2.4 GHz [a]
- Pin sources checked
- 2026-11-16
- Technical details reviewed
- 2026-11-14
Cautions for this board
- GPIO pins operate at 3.3 V and are not 5 V tolerant. Never apply 5 V to a GPIO pin; it can permanently damage the SoC. Source: [1]
- A single GPIO pin can supply up to 16 mA; all GPIO pins combined can supply at most 50 mA. Source: [1]
- On keyboard computers the header is on the rear and rotated 180° compared with a standard board; pins 1 and 40 are labelled. Check the orientation before connecting. Source: [2] [3]
- The Pi 500 product brief states it has the same processor and RP1 I/O controller as Pi 5, so the Pi 5 RP1 alternate-function table is used. Source: [4] [3] [5]
- RP1 GPIO levels: input low at most 0.8 V, input high at least 2.0 V; output high at least 2.9 V, output low at most 0.4 V. Drive strength is set to 2, 4, 8 or 12 mA. Source: [6]
All pins (40)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| 01 | 3V3 | Power | — | — | [7] [3] [4] |
| 02 | 5V | Power | — | — | [7] [3] [4] |
| 03 | GPIO2 | General-purpose I/O | SPI0_CSn[3] ALT0DPI_VSYNC ALT1UART1_CTS ALT2I2C1_SDA ALT3UART0_IR_RX ALT4SYS_RIO[2] ALT5PROC_RIO[2] ALT6PIO[2] ALT7SPI2_SIO[0] ALT8 | This pin has a fixed 1.8 kΩ on-board pull-up resistor to 3.3 V; it is not software-configurable. Source: [1] | [7] [3] [4] [1] |
| 04 | 5V | Power | — | — | [7] [3] [4] |
| 05 | GPIO3 | General-purpose I/O | SPI0_CSn[2] ALT0DPI_HSYNC ALT1UART1_RTS ALT2I2C1_SCL ALT3UART0_IR_TX ALT4SYS_RIO[3] ALT5PROC_RIO[3] ALT6PIO[3] ALT7SPI2_SCLK ALT8 | This pin has a fixed 1.8 kΩ on-board pull-up resistor to 3.3 V; it is not software-configurable. Source: [1] | [7] [3] [4] [1] |
| 06 | GND | Ground | — | — | [7] [3] [4] |
| 07 | GPIO4 | General-purpose I/O | GPCLK[0] ALT0DPI_D[0] ALT1UART2_TX ALT2I2C2_SDA ALT3UART0_RI ALT4SYS_RIO[4] ALT5PROC_RIO[4] ALT6PIO[4] ALT7SPI3_CSn[0] ALT8 | — | [7] [3] [4] |
| 08 | GPIO14 | General-purpose I/O | PWM0[2] ALT0DPI_D[10] ALT1UART4_CTS ALT2I2C3_SDA ALT3UART0_TX ALT4SYS_RIO[14] ALT5PROC_RIO[14] ALT6PIO[14] ALT7SPI5_SIO[0] ALT8 | — | [7] [3] [4] |
| 09 | GND | Ground | — | — | [7] [3] [4] |
| 10 | GPIO15 | General-purpose I/O | PWM0[3] ALT0DPI_D[11] ALT1UART4_RTS ALT2I2C3_SCL ALT3UART0_RX ALT4SYS_RIO[15] ALT5PROC_RIO[15] ALT6PIO[15] ALT7SPI5_SCLK ALT8 | — | [7] [3] [4] |
| 11 | GPIO17 | General-purpose I/O | SPI1_CSn[1] ALT0DPI_D[13] ALT1MIPI1_DSI_TE ALT2UART0_RTS ALT4SYS_RIO[17] ALT5PROC_RIO[17] ALT6PIO[17] ALT7 | — | [7] [3] [4] |
| 12 | GPIO18 | General-purpose I/O | SPI1_CSn[0] ALT0DPI_D[14] ALT1I2S0_SCLK ALT2PWM0[2] ALT3I2S1_SCLK ALT4SYS_RIO[18] ALT5PROC_RIO[18] ALT6PIO[18] ALT7GPCLK[1] ALT8 | — | [7] [3] [4] |
| 13 | GPIO27 | General-purpose I/O | SDIO0_DAT[3] ALT0DPI_D[23] ALT1I2S0_SDO[3] ALT2AUDIO_IN_DAT1 ALT3I2S1_SDO[3] ALT4SYS_RIO[27] ALT5PROC_RIO[27] ALT6PIO[27] ALT7SPI1_CSn[1] ALT8 | — | [7] [3] [4] |
| 14 | GND | Ground | — | — | [7] [3] [4] |
| 15 | GPIO22 | General-purpose I/O | SDIO0_CLK ALT0DPI_D[18] ALT1I2S0_SDI[1] ALT2I2C3_SDA ALT3I2S1_SDI[1] ALT4SYS_RIO[22] ALT5PROC_RIO[22] ALT6PIO[22] ALT7 | — | [7] [3] [4] |
| 16 | GPIO23 | General-purpose I/O | SDIO0_CMD ALT0DPI_D[19] ALT1I2S0_SDO[1] ALT2I2C3_SCL ALT3I2S1_SDO[1] ALT4SYS_RIO[23] ALT5PROC_RIO[23] ALT6PIO[23] ALT7 | — | [7] [3] [4] |
| 17 | 3V3 | Power | — | — | [7] [3] [4] |
| 18 | GPIO24 | General-purpose I/O | SDIO0_DAT[0] ALT0DPI_D[20] ALT1I2S0_SDI[2] ALT2I2S1_SDI[2] ALT4SYS_RIO[24] ALT5PROC_RIO[24] ALT6PIO[24] ALT7SPI2_CSn[1] ALT8 | — | [7] [3] [4] |
| 19 | GPIO10 | General-purpose I/O | SPI0_SIO[0] ALT0DPI_D[6] ALT1UART3_CTS ALT2I2C1_SDA ALT3SYS_RIO[10] ALT5PROC_RIO[10] ALT6PIO[10] ALT7SPI4_SIO[1] ALT8 | — | [7] [3] [4] |
| 20 | GND | Ground | — | — | [7] [3] [4] |
| 21 | GPIO9 | General-purpose I/O | SPI0_SIO[1] ALT0DPI_D[5] ALT1UART3_RX ALT2I2C0_SCL ALT3SYS_RIO[9] ALT5PROC_RIO[9] ALT6PIO[9] ALT7SPI4_SIO[0] ALT8 | — | [7] [3] [4] |
| 22 | GPIO25 | General-purpose I/O | SDIO0_DAT[1] ALT0DPI_D[21] ALT1I2S0_SDO[2] ALT2AUDIO_IN_CLK ALT3I2S1_SDO[2] ALT4SYS_RIO[25] ALT5PROC_RIO[25] ALT6PIO[25] ALT7SPI3_CSn[1] ALT8 | — | [7] [3] [4] |
| 23 | GPIO11 | General-purpose I/O | SPI0_SCLK ALT0DPI_D[7] ALT1UART3_RTS ALT2I2C1_SCL ALT3SYS_RIO[11] ALT5PROC_RIO[11] ALT6PIO[11] ALT7SPI4_SCLK ALT8 | — | [7] [3] [4] |
| 24 | GPIO8 | General-purpose I/O | SPI0_CSn[0] ALT0DPI_D[4] ALT1UART3_TX ALT2I2C0_SDA ALT3SYS_RIO[8] ALT5PROC_RIO[8] ALT6PIO[8] ALT7SPI4_CSn[0] ALT8 | — | [7] [3] [4] |
| 25 | GND | Ground | — | — | [7] [3] [4] |
| 26 | GPIO7 | General-purpose I/O | SPI0_CSn[1] ALT0DPI_D[3] ALT1UART2_RTS ALT2I2C3_SCL ALT3UART0_DSR ALT4SYS_RIO[7] ALT5PROC_RIO[7] ALT6PIO[7] ALT7SPI3_SCLK ALT8 | — | [7] [3] [4] |
| 27 | GPIO0 | General-purpose I/O | SPI0_SIO[3] ALT0DPI_PCLK ALT1UART1_TX ALT2I2C0_SDA ALT3SYS_RIO[0] ALT5PROC_RIO[0] ALT6PIO[0] ALT7SPI2_CSn[0] ALT8 | Reserved for HAT EEPROM Reserved for the HAT identification EEPROM; do not plan it as a general project GPIO. | [7] [3] [4] |
| 28 | GPIO1 | General-purpose I/O | SPI0_SIO[2] ALT0DPI_DE ALT1UART1_RX ALT2I2C0_SCL ALT3SYS_RIO[1] ALT5PROC_RIO[1] ALT6PIO[1] ALT7SPI2_SIO[1] ALT8 | Reserved for HAT EEPROM Reserved for the HAT identification EEPROM; do not plan it as a general project GPIO. | [7] [3] [4] |
| 29 | GPIO5 | General-purpose I/O | GPCLK[1] ALT0DPI_D[1] ALT1UART2_RX ALT2I2C2_SCL ALT3UART0_DTR ALT4SYS_RIO[5] ALT5PROC_RIO[5] ALT6PIO[5] ALT7SPI3_SIO[1] ALT8 | — | [7] [3] [4] |
| 30 | GND | Ground | — | — | [7] [3] [4] |
| 31 | GPIO6 | General-purpose I/O | GPCLK[2] ALT0DPI_D[2] ALT1UART2_CTS ALT2I2C3_SDA ALT3UART0_DCD ALT4SYS_RIO[6] ALT5PROC_RIO[6] ALT6PIO[6] ALT7SPI3_SIO[0] ALT8 | — | [7] [3] [4] |
| 32 | GPIO12 | General-purpose I/O | PWM0[0] ALT0DPI_D[8] ALT1UART4_TX ALT2I2C2_SDA ALT3AUDIO_OUT_L ALT4SYS_RIO[12] ALT5PROC_RIO[12] ALT6PIO[12] ALT7SPI5_CSn[0] ALT8 | — | [7] [3] [4] |
| 33 | GPIO13 | General-purpose I/O | PWM0[1] ALT0DPI_D[9] ALT1UART4_RX ALT2I2C2_SCL ALT3AUDIO_OUT_R ALT4SYS_RIO[13] ALT5PROC_RIO[13] ALT6PIO[13] ALT7SPI5_SIO[1] ALT8 | — | [7] [3] [4] |
| 34 | GND | Ground | — | — | [7] [3] [4] |
| 35 | GPIO19 | General-purpose I/O | SPI1_SIO[1] ALT0DPI_D[15] ALT1I2S0_WS ALT2PWM0[3] ALT3I2S1_WS ALT4SYS_RIO[19] ALT5PROC_RIO[19] ALT6PIO[19] ALT7 | — | [7] [3] [4] |
| 36 | GPIO16 | General-purpose I/O | SPI1_CSn[2] ALT0DPI_D[12] ALT1MIPI0_DSI_TE ALT2UART0_CTS ALT4SYS_RIO[16] ALT5PROC_RIO[16] ALT6PIO[16] ALT7 | — | [7] [3] [4] |
| 37 | GPIO26 | General-purpose I/O | SDIO0_DAT[2] ALT0DPI_D[22] ALT1I2S0_SDI[3] ALT2AUDIO_IN_DAT0 ALT3I2S1_SDI[3] ALT4SYS_RIO[26] ALT5PROC_RIO[26] ALT6PIO[26] ALT7SPI5_CSn[1] ALT8 | — | [7] [3] [4] |
| 38 | GPIO20 | General-purpose I/O | SPI1_SIO[0] ALT0DPI_D[16] ALT1I2S0_SDI[0] ALT2GPCLK[0] ALT3I2S1_SDI[0] ALT4SYS_RIO[20] ALT5PROC_RIO[20] ALT6PIO[20] ALT7 | — | [7] [3] [4] |
| 39 | GND | Ground | — | — | [7] [3] [4] |
| 40 | GPIO21 | General-purpose I/O | SPI1_SCLK ALT0DPI_D[17] ALT1I2S0_SDO[0] ALT2GPCLK[1] ALT3I2S1_SDO[0] ALT4SYS_RIO[21] ALT5PROC_RIO[21] ALT6PIO[21] ALT7 | — | [7] [3] [4] |
Model-specific features and connection notes
Sources
Pin and warning references
- Raspberry Pi GPIO documentationGPIO pads and voltage · 3.3 V only warning, fixed GP2/GP3 pull-ups, per-pin and total current
- Raspberry Pi GPIO documentationPin layout · header on the rear of keyboard computers, rotated 180°, pins 1 and 40 labelled
- Raspberry Pi keyboard computers documentationSpecifications table · SoC and I/O controller (BCM2712 + RP1) and GPIO (horizontal 40-pin header) rows
- Raspberry Pi 500 Product Brief · PDF p. 2Overview · same processor and RP1 I/O controller as Raspberry Pi 5; Specification · horizontal 40-pin GPIO header
- Raspberry Pi RP1 Peripherals · PDF p. 16§3.1.1 · Table 4 · GPIO function selection a0–a8
- Raspberry Pi GPIO documentationVoltage specifications · RP1 products table (Raspberry Pi 5, 500, 500+)
- Raspberry Pi GPIO documentationPin names, types, and typical functions · all 40 header rows
Technical sources (6)
- Raspberry Pi 5 specificationsRaspberry Pi · Specification
- Raspberry Pi 500 Product BriefRaspberry Pi Ltd · Overview and Specification · Cortex-A76 @ 2.4 GHz with RP1, 8 GB LPDDR4X-4267, 5 V DC via USB, microSD; locked in sources/manifest.json
- Raspberry Pi keyboard computers documentationRaspberry Pi Ltd · Specifications table · Raspberry Pi 500 power input 5 V / 5 A USB-C with a 600 mA peripheral limit; locked in sources/manifest.json
- Raspberry Pi 500 and Raspberry Pi Monitor on sale nowRaspberry Pi · Publication date (2024-12-09)
- Raspberry Pi GPIO documentationManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- Raspberry Pi RP1 PeripheralsRaspberry Pi Ltd · Locked pin-source document; see sources/manifest.json for revision and SHA-256
Locked source documents
- Raspberry Pi RP1 Peripheralsbuild b9b6f74-clean · 2023-11-07
- Raspberry Pi GPIO documentation0fb416315f8f6c1949c0614989075d3e5805104b
- Raspberry Pi 500 Product BriefRaspberry Pi Ltd · RP-008349-DS-4 · published April 2026
- Raspberry Pi keyboard computers documentationRaspberry Pi Ltd · 0fb416315f8f6c1949c0614989075d3e5805104b