Development boards
Raspberry Pi RM2 pinout
CYW43439 · Wi-Fi 4 + Bluetooth 5.2 · 21-pad SMT module
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
21 castellated SMT edge pads. Infineon CYW43439 radio IC; single-band 2.4 GHz Wi-Fi 4 (802.11n) and Bluetooth 5.2. Controlled over gSPI via the Pico SDK; includes 3 host-controlled GPIO expander pins (GPIO0-2).
At a glance
- Platform / manufacturer
- Raspberry Pi
- Type
- Development boards
- MCU
- CYW43439
- Package / connector
- 21-pad castellated SMT module
- Physical contacts
- 21
- GPIO
- 3
- I/O voltage
- 1.8 V / 3.3 V I/O
- Interfaces (pin count)
- SPI (4) · GPIO (3) · IRQ (1) · SYSTEM (2)
- Initial sale / release date
- 2024-11-20 [b]
- MCU / processor core
- Embedded Arm Cortex-M3 (WLAN/BT subsystem) [a]
- Clock speed / maximum
- 37.4 MHz reference [a]
- Internal RAM / system RAM
- Internal WLAN/BT RAM & ROM [a]
- Power and logic level
- VIN: 3.0 to 4.8 V (nominal 3.3 V); VDDIO: 1.8 V +/-5% or 3.3 V +/-5%. Match VDDIO logic levels to the host microcontroller. [b] [a]
- Pin sources checked
- 2026-11-16
- Technical details reviewed
- 2026-11-14
All pins (21)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| Pin 1 | GND | Ground | — | — | [1] |
| Pin 2 | NC | System | — | No connection (NC). Leave unconnected; do not wire to external circuits. | [1] |
| Pin 3 | gSPI_SCLKBoard label SCLK | System | gSPI CLK | gSPI serial clock (SCLK). Connects to Pico GPIO29 by default (approx 31.25 MHz gSPI clock). | [1] |
| Pin 4 | GND | Ground | — | — | [1] |
| Pin 5 | gSPI_MOSIBoard label DIN | System | gSPI DIN | gSPI serial data input (Data In / MOSI). Connects directly to Pico GPIO24 by default. | [1] |
| Pin 6 | gSPI_MISOBoard label DOUT | System | gSPI DOUT | Requires a 470 ohm series resistor (gSPI Data Out line) gSPI serial data output (Data Out / MISO). Connects to Pico GPIO24 through a 470 ohm series resistor in the Pico SDK. | [1] |
| Pin 7 | GND | Ground | — | — | [1] |
| Pin 8 | GPIO0 | General-purpose I/O | GPIO0 | CYW43439 internal GPIO0 expander pin. Used on Pico W to drive the onboard user LED. | [1] |
| Pin 9 | gSPI_CSBoard label CS | System | gSPI CS | gSPI chip select (CS). Connects to Pico GPIO25 by default. | [1] |
| Pin 10 | nIRQ | System | nIRQ | Requires a 10 k ohm series resistor (nIRQ line) CYW43 interrupt line (nIRQ). Connects to Pico GPIO24 through a 10 k ohm series resistor to notify host of incoming data. | [1] |
| Pin 11 | GND | Ground | — | — | [1] |
| Pin 12 | WL_REG_ONBoard label WL_ON | System | WL_REG_ON | Wi-Fi power-up regulator enable input (WL_REG_ON). Connects to Pico GPIO23 by default. | [1] |
| Pin 13 | BT_REG_ONBoard label BT_ON | System | BT_REG_ON | Bluetooth power-up regulator enable input (BT_REG_ON). Connects to Pico GPIO23 by default. | [1] |
| Pin 14 | VDDIO | Power | — | I/O supply voltage (VDDIO). 1.8 V +/-5% or 3.3 V +/-5%; must match host microcontroller logic levels. | [1] |
| Pin 15 | GND | Ground | — | — | [1] |
| Pin 16 | VIN | Power | — | Main power input (VIN). 3.0 V to 4.8 V range (nominal 3.3 V). Voltages below 3.2 V reduce RF performance. | [1] |
| Pin 17 | GPIO2 | General-purpose I/O | GPIO2 | CYW43439 internal GPIO2 expander pin. Controlled by the host processor via the wireless chip. | [1] |
| Pin 18 | GPIO1 | General-purpose I/O | GPIO1 | CYW43439 internal GPIO1 expander pin. Controlled by the host processor via the wireless chip. | [1] |
| Pin 19 | NC | System | — | No connection (NC). Leave unconnected; do not wire to external circuits. | [1] |
| Pin 20 | NC | System | — | No connection (NC). Leave unconnected; do not wire to external circuits. | [1] |
| Pin 21 | GND | Ground | — | — | [1] |
Model-specific features and connection notes
Sources
Pin and warning references
- Raspberry Pi Radio Module 2 Datasheet · PDF p. 11Table 2 · The function of each pin on a Raspberry Pi Radio Module 2
Technical sources (2)
- Raspberry Pi Radio Module 2 DatasheetRaspberry Pi Ltd · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- Raspberry Pi Radio Module 2 Product DocumentationRaspberry Pi Ltd · Official product documentation, hardware integration and pinout
Locked source documents
- Raspberry Pi Radio Module 2 DatasheetRaspberry Pi Ltd · RP-008943-DS-7