Development boards
Raspberry Pi Pico 2 W pinout
RP2350A · 40-pin development board
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
At a glance
- Platform / manufacturer
- Raspberry Pi
- Type
- Development boards
- MCU
- RP2350A
- Physical contacts
- 40
- GPIO
- 26
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (26) · SPI (26) · UART (26) · USB (26) · ADC (3) · PWM (26) · CLOCK (12) · HSTX (8) · PIO (26) · QMI (3) · SIO (26)
- Initial sale / release date
- 2024-11-25 [d]
- MCU / processor core
- 2 × Arm Cortex-M33 / 2 × Hazard3 RISC-V [a]
- Clock speed / maximum
- 150 MHz [a]
- Internal RAM / system RAM
- 520 KB SRAM [a]
- Fixed ROM / boot ROM
- 32 KB boot ROM [a]
- Power and logic level
- USB: 5 V; VSYS: 1.8–5.5 V. GPIO logic: 3.3 V; 5.5 V input tolerance only under datasheet conditions. [b] [c]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
Cautions for this board
- RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]
All pins (40)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| 01 | GP0MCU pin 2 | General-purpose I/O | SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 02 | GP1MCU pin 3 | General-purpose I/O | SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACECLK F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 03 | GND | Ground | — | — | [2] |
| 04 | GP2MCU pin 4 | General-purpose I/O | SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA0 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 05 | GP3MCU pin 5 | General-purpose I/O | SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 06 | GP4MCU pin 7 | General-purpose I/O | SPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA2 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 07 | GP5MCU pin 8 | General-purpose I/O | SPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA3 F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 08 | GND | Ground | — | — | [2] |
| 09 | GP6MCU pin 9 | General-purpose I/O | SPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 10 | GP7MCU pin 10 | General-purpose I/O | SPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 11 | GP8MCU pin 12 | General-purpose I/O | SPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 12 | GP9MCU pin 13 | General-purpose I/O | SPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 13 | GND | Ground | — | — | [2] |
| 14 | GP10MCU pin 14 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 15 | GP11MCU pin 15 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 16 | GP12MCU pin 16 | General-purpose I/O | HSTX F0SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 17 | GP13MCU pin 17 | General-purpose I/O | HSTX F0SPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 18 | GND | Ground | — | — | [2] |
| 19 | GP14MCU pin 18 | General-purpose I/O | HSTX F0SPI1 SCK F1UART0 CTS F2I2C1 SDA F3PWM7 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 20 | GP15MCU pin 19 | General-purpose I/O | HSTX F0SPI1 TX F1UART0 RTS F2I2C1 SCL F3PWM7 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 21 | GP16MCU pin 27 | General-purpose I/O | HSTX F0SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 22 | GP17MCU pin 28 | General-purpose I/O | HSTX F0SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 23 | GND | Ground | — | — | [2] |
| 24 | GP18MCU pin 29 | General-purpose I/O | HSTX F0SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 25 | GP19MCU pin 31 | General-purpose I/O | HSTX F0SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 26 | GP20MCU pin 32 | General-purpose I/O | SPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 27 | GP21MCU pin 33 | General-purpose I/O | SPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 28 | GND | Ground | — | — | [2] |
| 29 | GP22MCU pin 34 | General-purpose I/O | SPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 30 | RUNMCU pin 26 | System | — | Pull RUN low to reset the RP2350. Source: [5] | [2] [5] [6] |
| 31 | GP26MCU pin 40 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 TX F11ADC0 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 32 | GP27MCU pin 41 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 RX F11ADC1 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 33 | AGND | Ground | — | Analog ground reference for the ADC. Source: [5] | [2] [5] |
| 34 | GP28MCU pin 42 | General-purpose I/O | SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10ADC2 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [1] |
| 35 | ADC_VREF | Analog | — | Dedicated ADC supply and reference connection. Source: [5] | [2] [5] |
| 36 | 3V3(OUT) | Power | — | Regulated 3.3 V output from the board. Source: [5] | [2] [5] |
| 37 | 3V3_EN | System | — | Dedicated regulator enable input. Source: [5] | [2] [5] |
| 38 | GND | Ground | — | — | [2] |
| 39 | VSYS | Power | — | Main supply input, rated for 1.8–5.5 V. Source: [5] | [2] [5] |
| 40 | VBUS | Power | — | USB VBUS, nominally 5 V when powered over USB. Source: [5] | [2] [5] |
Model-specific features and connection notes
Sources
Pin and warning references
- RP2350 Datasheet · PDF p. 1359Appendix D.5.1 · RP2350-E9 · increased leakage on Bank 0 GPIO inputs (A2 stepping; pp. 1359–1360)
- Raspberry Pi Pico 2 W Pinout · PDF p. 1Manufacturer 40-pin diagram; physical pin names visually checked
- RP2350 Datasheet · PDF p. 1332§14.8.2.1 · Table 1673 · FT input conditions; pin types in Tables 1674–1679
- RP2350 Datasheet · PDF p. 1333§14.8.2.2 · Tables 1674–1679 · package pin list
- Raspberry Pi Pico 2 W Datasheet · PDF p. 9§2.1 · special supply / analogue / RUN pins
- RP2350 Datasheet · PDF p. 1335§14.8.2.2 · Tables 1674–1679 · package pin list
Technical sources (4)
- RP2350 DatasheetManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- Pico series specificationsRaspberry Pi · Key features and board variants
- Raspberry Pi Pico 2 W DatasheetManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- pico2w launch announcementRaspberry Pi · Publication date / product announcement
Locked source documents
- RP2350 DatasheetRelease 8 · 2026-10-01
- Raspberry Pi Pico 2 W DatasheetRelease 2 · 2026-07-03
- Raspberry Pi Pico 2 W PinoutRP-008305-DS-1