Development boards
Raspberry Pi Zero 2 W pinout
J8 · 40-pin footprint (unpopulated) · RP3A0 (BCM2710A1) alternate functions
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
Zero 2 W ships with an unpopulated footprint for a HAT-compatible 40-pin GPIO header (the “with headers” model has it fitted). Pin numbers follow the standard 40-pin layout. The mini HDMI and two micro USB ports are not header pins. The BCM2835 table is used for the BCM2710A1 inside RP3A0.
At a glance
- Platform / manufacturer
- Raspberry Pi
- Type
- Development boards
- MCU
- RP3A0 (BCM2710A1)
- Physical contacts
- 40
- GPIO
- 28 (2 reserved)
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (4) · SPI (11) · UART (4) · PWM (4) · CLOCK (5) · JTAG (11) · PCM (4) · SDIO (6) · SMI (26) · SYSTEM (4)
- Initial sale / release date
- 2021-10-28 [c]
- Power and logic level
- 5 V DC 2.5 A via micro USB [b]
- Pin sources checked
- 2026-11-16
- Technical details reviewed
- 2026-11-14
Cautions for this board
- GPIO pins operate at 3.3 V and are not 5 V tolerant. Never apply 5 V to a GPIO pin; it can permanently damage the SoC. Source: [1]
- A single GPIO pin can supply up to 16 mA; all GPIO pins combined can supply at most 50 mA. Source: [1]
- The 40-pin header is unpopulated on this model. Solder a 2 × 20, 2.54 mm pin header for GPIO access, or use the model with the header fitted. Source: [2] [3] [4]
- Alternate functions come from the BCM2835 ARM Peripherals GPIO table (§6.2). Raspberry Pi processor documentation states that BCM2710A1 is the BCM2837 die, that BCM2837B0 shares the BCM2837 architecture, and that BCM2837 and BCM2836 are the BCM2835 architecture with different Arm cores. The document contains known errors. Pi 4-only UART2–5, SPI3–6, I²C3–6 and DPI selections are not in this table and are not shown. Source: [5] [6] [7] [8] [9] [10]
- BCM2835/BCM2836/BCM2837/RP3A0 GPIO levels: input low at most 0.9 V, input high at least 1.6 V (hysteresis enabled). Default drive strength 8 mA, maximum 16 mA; internal pull-up/pull-down 50–65 kΩ. Source: [11]
All pins (40)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| 01 | 3V3 | Power | — | — | [12] [4] |
| 02 | 5V | Power | — | — | [12] [4] |
| 03 | GPIO2 | General-purpose I/O | I2C1 SDA ALT0SA3 ALT1 | This pin has a fixed 1.8 kΩ on-board pull-up resistor to 3.3 V; it is not software-configurable. Source: [1] | [12] [4] [1] |
| 04 | 5V | Power | — | — | [12] [4] |
| 05 | GPIO3 | General-purpose I/O | I2C1 SCL ALT0SA2 ALT1 | This pin has a fixed 1.8 kΩ on-board pull-up resistor to 3.3 V; it is not software-configurable. Source: [1] | [12] [4] [1] |
| 06 | GND | Ground | — | — | [12] [4] |
| 07 | GPIO4 | General-purpose I/O | GPCLK0 ALT0SA1 ALT1ARM_TDI ALT5 | — | [12] [4] |
| 08 | GPIO14 | General-purpose I/O | UART0 TX ALT0SD6 ALT1UART1 TX ALT5 | — | [12] [4] |
| 09 | GND | Ground | — | — | [12] [4] |
| 10 | GPIO15 | General-purpose I/O | UART0 RX ALT0SD7 ALT1UART1 RX ALT5 | — | [12] [4] |
| 11 | GPIO17 | General-purpose I/O | SD9 ALT1UART0 RTS ALT3SPI1_CE1_N ALT4UART1 RTS ALT5 | — | [12] [4] |
| 12 | GPIO18 | General-purpose I/O | PCM_CLK ALT0SD10 ALT1BSCSL SDA / MOSI ALT3SPI1_CE0_N ALT4PWM0 ALT5 | — | [12] [4] |
| 13 | GPIO27 | General-purpose I/O | SD1_DAT3 ALT3ARM_TMS ALT4 | — | [12] [4] |
| 14 | GND | Ground | — | — | [12] [4] |
| 15 | GPIO22 | General-purpose I/O | SD14 ALT1SD1_CLK ALT3ARM_TRST ALT4 | — | [12] [4] |
| 16 | GPIO23 | General-purpose I/O | SD15 ALT1SD1_CMD ALT3ARM_RTCK ALT4 | — | [12] [4] |
| 17 | 3V3 | Power | — | — | [12] [4] |
| 18 | GPIO24 | General-purpose I/O | SD16 ALT1SD1_DAT0 ALT3ARM_TDO ALT4 | — | [12] [4] |
| 19 | GPIO10 | General-purpose I/O | SPI0_MOSI ALT0SD2 ALT1 | — | [12] [4] |
| 20 | GND | Ground | — | — | [12] [4] |
| 21 | GPIO9 | General-purpose I/O | SPI0_MISO ALT0SD1 ALT1 | — | [12] [4] |
| 22 | GPIO25 | General-purpose I/O | SD17 ALT1SD1_DAT1 ALT3ARM_TCK ALT4 | — | [12] [4] |
| 23 | GPIO11 | General-purpose I/O | SPI0_SCLK ALT0SD3 ALT1 | — | [12] [4] |
| 24 | GPIO8 | General-purpose I/O | SPI0_CE0_N ALT0SD0 ALT1 | — | [12] [4] |
| 25 | GND | Ground | — | — | [12] [4] |
| 26 | GPIO7 | General-purpose I/O | SPI0_CE1_N ALT0SWE_N / SRW_N ALT1 | — | [12] [4] |
| 27 | GPIO0 | General-purpose I/O | I2C0 SDA ALT0SA5 ALT1 | Reserved for HAT EEPROM Reserved for the HAT identification EEPROM; do not plan it as a general project GPIO. | [12] [4] |
| 28 | GPIO1 | General-purpose I/O | I2C0 SCL ALT0SA4 ALT1 | Reserved for HAT EEPROM Reserved for the HAT identification EEPROM; do not plan it as a general project GPIO. | [12] [4] |
| 29 | GPIO5 | General-purpose I/O | GPCLK1 ALT0SA0 ALT1ARM_TDO ALT5 | — | [12] [4] |
| 30 | GND | Ground | — | — | [12] [4] |
| 31 | GPIO6 | General-purpose I/O | GPCLK2 ALT0SOE_N / SE ALT1ARM_RTCK ALT5 | — | [12] [4] |
| 32 | GPIO12 | General-purpose I/O | PWM0 ALT0SD4 ALT1ARM_TMS ALT5 | — | [12] [4] |
| 33 | GPIO13 | General-purpose I/O | PWM1 ALT0SD5 ALT1ARM_TCK ALT5 | — | [12] [4] |
| 34 | GND | Ground | — | — | [12] [4] |
| 35 | GPIO19 | General-purpose I/O | PCM_FS ALT0SD11 ALT1BSCSL SCL / SCLK ALT3SPI1_MISO ALT4PWM1 ALT5 | — | [12] [4] |
| 36 | GPIO16 | General-purpose I/O | SD8 ALT1UART0 CTS ALT3SPI1_CE2_N ALT4UART1 CTS ALT5 | — | [12] [4] |
| 37 | GPIO26 | General-purpose I/O | SD1_DAT2 ALT3ARM_TDI ALT4 | — | [12] [4] |
| 38 | GPIO20 | General-purpose I/O | PCM_DIN ALT0SD12 ALT1BSCSL / MISO ALT3SPI1_MOSI ALT4GPCLK0 ALT5 | — | [12] [4] |
| 39 | GND | Ground | — | — | [12] [4] |
| 40 | GPIO21 | General-purpose I/O | PCM_DOUT ALT0SD13 ALT1BSCSL / CE_N ALT3SPI1_SCLK ALT4GPCLK1 ALT5 | — | [12] [4] |
Model-specific features and connection notes
Sources
Pin and warning references
- Raspberry Pi GPIO documentationGPIO pads and voltage · 3.3 V only warning, fixed GP2/GP3 pull-ups, per-pin and total current
- Raspberry Pi Zero models documentation · introduction and model listZero models · common ports (mini HDMI, 2 × micro USB), unpopulated header on models without H / "with headers", model list table
- Raspberry Pi Zero 2 W Product Brief · PDF p. 2Overview and Specification · RP3A0 / BCM2710A1, unpopulated HAT-compatible 40-pin header footprint
- Raspberry Pi Zero 2 W Reduced Schematics · PDF p. 1J8 · GPIO net labels matched to contacts · footprint marked DNF (not fitted); power and ground visually checked
- BCM2835 ARM Peripherals · PDF p. 102§6.2 · Alternative Function Assignments · GPIO0–27 ALT0–ALT5, applied to BCM2837B0 / RP3A0 (BCM2710A1) because Raspberry Pi documents them as BCM2835-architecture devices
- Raspberry Pi processors documentation · RP3A0RP3A0 · BCM2710A1 is the die inside BCM2837; used by Raspberry Pi Zero 2 W
- Raspberry Pi processors documentation · BCM2837BCM2837 · underlying architecture identical to BCM2836
- Raspberry Pi processors documentation · BCM2836BCM2836 · underlying architecture identical to BCM2835
- Raspberry Pi processors documentation · BCM2835BCM2835 · used in Raspberry Pi Zero W; peripheral specification and its known-errors note
- Raspberry Pi GPIO documentationPin functions · BCM2835 peripherals datasheet named for earlier families and Zero models
- Raspberry Pi GPIO documentationVoltage specifications · BCM2835, BCM2836, BCM2837 and RP3A0 table (V_IL, V_IH, pulls, drive strength)
- Raspberry Pi GPIO documentationPin names, types, and typical functions · all 40 header rows
Technical sources (6)
- Raspberry Pi processors documentation · RP3A0Raspberry Pi Ltd · RP3A0 · BCM2710A1 with 512 MB DRAM, quad-core Cortex-A53 at 1 GHz; locked in sources/manifest.json
- Raspberry Pi Zero 2 W Product BriefRaspberry Pi Ltd · Overview and Specification · RP3A0 / BCM2710A1, 1 GHz, 512 MB LPDDR2, 5 V DC 2.5 A; locked in sources/manifest.json
- New product: Raspberry Pi Zero 2 W on sale nowRaspberry Pi · Publication date (2021-10-28)
- Raspberry Pi GPIO documentationManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- Raspberry Pi Zero 2 W Reduced SchematicsRaspberry Pi Ltd · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- BCM2835 ARM PeripheralsRaspberry Pi Ltd · Locked pin-source document; see sources/manifest.json for revision and SHA-256
Locked source documents
- Raspberry Pi GPIO documentation0fb416315f8f6c1949c0614989075d3e5805104b
- BCM2835 ARM PeripheralsRaspberry Pi Ltd · RP-008249-DS-1
- Raspberry Pi Zero 2 W Reduced SchematicsRaspberry Pi Ltd · RP-008360-DS-1
- Raspberry Pi Zero 2 W Product BriefRaspberry Pi Ltd · RP-008359-DS-1 · published April 2024
- Raspberry Pi processors documentation · BCM2835Raspberry Pi Ltd · 0fb416315f8f6c1949c0614989075d3e5805104b
- Raspberry Pi processors documentation · BCM2836Raspberry Pi Ltd · 0fb416315f8f6c1949c0614989075d3e5805104b
- Raspberry Pi processors documentation · BCM2837Raspberry Pi Ltd · 0fb416315f8f6c1949c0614989075d3e5805104b
- Raspberry Pi processors documentation · RP3A0Raspberry Pi Ltd · 0fb416315f8f6c1949c0614989075d3e5805104b
- Raspberry Pi Zero models documentation · introduction and model listRaspberry Pi Ltd · 0fb416315f8f6c1949c0614989075d3e5805104b