MCU packages
RP2350A pinout
QFN-60 · RP2350 · Release 8
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
At a glance
- Platform / manufacturer
- Raspberry Pi
- Type
- MCU packages
- MCU
- RP2350A
- Package / connector
- QFN-60
- Physical contacts
- 60
- GPIO
- 30
- I/O voltage
- 1.8–3.3 V I/O
- Interfaces (pin count)
- I²C (38) · SPI (30) · UART (38) · USB (30) · ADC (4) · PWM (30) · CLOCK (15) · HSTX (8) · PIO (30) · QMI (9) · SIO (38)
- Silicon introduction
- 2024-08-08 [b]
- MCU / processor core
- 2 × Arm Cortex-M33 / 2 × Hazard3 RISC-V [a]
- Clock speed / maximum
- 150 MHz [a]
- Internal RAM / system RAM
- 520 KB SRAM [a]
- Program Flash / storage
- No internal Flash; external QSPI Flash required. [a]
- Fixed ROM / boot ROM
- 32 KB boot ROM [a]
- Power and logic level
- Connect every supply, ground and exposed pad per datasheet; no board regulator is included. [a]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
Cautions for this board
- RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]
All pins (60)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| 01 | IOVDD | Power | — | — | [2] |
| 02 | GPIO0 | General-purpose I/O | SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 03 | GPIO1 | General-purpose I/O | SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACECLK F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 04 | GPIO2 | General-purpose I/O | SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA0 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 05 | GPIO3 | General-purpose I/O | SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 06 | DVDD | Power | — | — | [5] |
| 07 | GPIO4 | General-purpose I/O | SPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA2 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 08 | GPIO5 | General-purpose I/O | SPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA3 F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 09 | GPIO6 | General-purpose I/O | SPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 10 | GPIO7 | General-purpose I/O | SPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 11 | IOVDD | Power | — | — | [2] |
| 12 | GPIO8 | General-purpose I/O | SPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 13 | GPIO9 | General-purpose I/O | SPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 14 | GPIO10 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 15 | GPIO11 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 16 | GPIO12 | General-purpose I/O | HSTX F0SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 17 | GPIO13 | General-purpose I/O | HSTX F0SPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 18 | GPIO14 | General-purpose I/O | HSTX F0SPI1 SCK F1UART0 CTS F2I2C1 SDA F3PWM7 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 19 | GPIO15 | General-purpose I/O | HSTX F0SPI1 TX F1UART0 RTS F2I2C1 SCL F3PWM7 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 20 | IOVDD | Power | — | — | [2] |
| 21 | XIN | System | — | — | [5] |
| 22 | XOUT | System | — | — | [5] |
| 23 | DVDD | Power | — | — | [5] |
| 24 | SWCLK | System | — | — | [5] |
| 25 | SWDIO | System | — | — | [5] |
| 26 | RUN | System | — | — | [5] |
| 27 | GPIO16 | General-purpose I/O | HSTX F0SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 28 | GPIO17 | General-purpose I/O | HSTX F0SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 29 | GPIO18 | General-purpose I/O | HSTX F0SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 30 | IOVDD | Power | — | — | [2] |
| 31 | GPIO19 | General-purpose I/O | HSTX F0SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 32 | GPIO20 | General-purpose I/O | SPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 33 | GPIO21 | General-purpose I/O | SPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 34 | GPIO22 | General-purpose I/O | SPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 35 | GPIO23 | General-purpose I/O | SPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB VBUS EN F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 36 | GPIO24 | General-purpose I/O | SPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT2 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 37 | GPIO25 | General-purpose I/O | SPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT3 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 38 | IOVDD | Power | — | — | [2] |
| 39 | DVDD | Power | — | — | [5] |
| 40 | GPIO26_ADC0 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 TX F11ADC0 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 41 | GPIO27_ADC1 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 RX F11ADC1 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 42 | GPIO28_ADC2 | General-purpose I/O | SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10ADC2 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [3] [4] [1] |
| 43 | GPIO29_ADC3 | General-purpose I/O | SPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10ADC3 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [6] [4] [1] |
| 44 | ADC_AVDD | Power | — | — | [5] |
| 45 | IOVDD | Power | — | — | [2] |
| 46 | VREG_AVDD | Power | — | — | [5] |
| 47 | VREG_PGND | Ground | — | — | [5] |
| 48 | VREG_LX | System | — | — | [5] |
| 49 | VREG_VIN | Power | — | — | [5] |
| 50 | VREG_FB | System | — | — | [7] |
| 51 | USB_DM | System | UART1 RX F2I2C0 SCL F3SIO F5 | — | [5] |
| 52 | USB_DP | System | UART1 TX F2I2C0 SDA F3SIO F5 | — | [5] |
| 53 | USB_OTP_VDD | Power | — | — | [5] |
| 54 | QSPI_IOVDD | Power | — | — | [5] |
| 55 | QSPI_SD3 | System | QMI SD3 F0UART0 RTS F2I2C1 SCL F3SIO F5UART0 RX F11 | — | [6] |
| 56 | QSPI_SCLK | System | QMI SCK F0UART1 CTS F2I2C1 SDA F3SIO F5UART1 TX F11 | — | [6] |
| 57 | QSPI_SD0 | System | QMI SD0 F0UART0 TX F2I2C0 SDA F3SIO F5 | — | [6] |
| 58 | QSPI_SD2 | System | QMI SD2 F0UART0 CTS F2I2C1 SDA F3SIO F5UART0 TX F11 | — | [6] |
| 59 | QSPI_SD1 | System | QMI SD1 F0UART0 RX F2I2C0 SCL F3SIO F5 | — | [6] |
| 60 | QSPI_SS | System | QMI CS0n F0UART1 RTS F2I2C1 SCL F3SIO F5UART1 RX F11 | — | [6] |
Model-specific features and connection notes
- Two cores run concurrently; all four cores cannot run together. 12 PIO state machines. [a]
Sources
Pin and warning references
- RP2350 Datasheet · PDF p. 1359Appendix D.5.1 · RP2350-E9 · increased leakage on Bank 0 GPIO inputs (A2 stepping; pp. 1359–1360)
- RP2350 Datasheet · PDF p. 16§1.2.1 · Figure 2 · IOVDD pads (Table 1679 discrepancy reviewed)
- RP2350 Datasheet · PDF p. 1333§14.8.2.2 · Tables 1674–1679 · package pin list
- RP2350 Datasheet · PDF p. 1332§14.8.2.1 · Table 1673 · FT input conditions; pin types in Tables 1674–1679
- RP2350 Datasheet · PDF p. 1335§14.8.2.2 · Tables 1674–1679 · package pin list
- RP2350 Datasheet · PDF p. 1334§14.8.2.2 · Tables 1674–1679 · package pin list
- RP2350 Datasheet · PDF p. 1336§14.8.2.2 · Tables 1674–1679 · package pin list
Technical sources (2)
- RP2350 DatasheetManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- pico2 launch announcementRaspberry Pi · Publication date / product announcement
Locked source documents
- RP2350 DatasheetRelease 8 · 2026-10-01
More Raspberry Pi profiles
- Raspberry Pi Pico
- Raspberry Pi Pico 2
- Raspberry Pi Pico 2 W
- Raspberry Pi Pico W
- Raspberry Pi · 40-pin GPIO
- Raspberry Pi 3 Model B+
- Raspberry Pi 4 Model B
- Raspberry Pi 5
- Raspberry Pi 500
- Raspberry Pi Zero 2 W
- Raspberry Pi Zero W
- Raspberry Pi Compute Module 4
- Raspberry Pi Compute Module 5
- Raspberry Pi RM2
- RP2040
- RP2350B