Development boards

Arduino UNO R4 Minima pinout

Renesas RA4M1 · 48 MHz · 5 V I/O

Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe

USB at top. 32 shared UNO contacts and 6 SPI contacts; 20 independent 5 V GPIOs. The first power-header contact is BOOT. A0 provides a true DAC; CAN0 TX/RX uses D4/D5 and needs an external CAN transceiver. Observe the 8 mA per-pin and 60 mA total limits. The SWD/debug header is outside this view.

At a glance

Platform / manufacturer
Arduino
Type
Development boards
MCU
Renesas RA4M1
Physical contacts
38
GPIO
20
I/O voltage
5 V I/O
Interfaces (pin count)
I²C (4) · SPI (7) · UART (2) · CAN (2) · ADC (8) · DAC (1) · PWM (7)
Initial sale / release date
2023-06-26 [c]
MCU / processor core
Arm Cortex-M4F [a]
Clock speed / maximum
48 MHz [a] [b]
Internal RAM / system RAM
32 KB SRAM [a]
Program Flash / storage
256 KB Flash [a]
EEPROM / persistent data
8 KB data Flash (EEPROM emulation) [a]
Power and logic level
USB: 5 V; header GPIO: 5 V. See the board manual for VIN limits. [a] [b]
Pin sources checked
2026-11-15
Technical details reviewed
2026-11-14

All pins (38)

Arduino UNO R4 Minima: every pin in physical order with its type, functions and warnings
PhysicalPin nameTypeFunctionsNotes and warningsSource
PWR.1BOOTSystem—

RA4M1 boot-mode contact, not a general-purpose GPIO. Follow the board's boot/programming instructions.

[1]
PWR.2IOREFPower—

Board reference for digital logic voltage; connected to 5 V on this board. Source: [2]

[1] [2]
PWR.3RESETSystem—

Same electrical signal as ICSP.5

Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit.

[1]
PWR.43V3Power——[1]
PWR.55VPower——[1]
PWR.6GNDGround——[1]
PWR.7GNDGround——[1]
PWR.8VINPower—

Unregulated power input, not GPIO. Check the board datasheet for the input range and regulator thermal limits.

[1]
ANALOG.1A0Arduino D14 · MCU port P014General-purpose I/OAN009DAC0—[1] [3]
ANALOG.2A1Arduino D15 · MCU port P000General-purpose I/OAN000—[1] [3]
ANALOG.3A2Arduino D16 · MCU port P001General-purpose I/OAN001—[1] [3]
ANALOG.4A3Arduino D17 · MCU port P002General-purpose I/OAN002—[1] [3]
ANALOG.5A4Arduino D18 · MCU port P101General-purpose I/OI2C SDAAN021

Same electrical signal as DIGITAL.17

[1] [3]
ANALOG.6A5Arduino D19 · MCU port P100General-purpose I/OI2C SCLAN022

Same electrical signal as DIGITAL.18

[1] [3]
DIGITAL.1D0Arduino D0 · MCU port P301General-purpose I/OSerial1 RX

Header Serial1 connects to the RA4M1 SCI2 peripheral. USB Serial and the WiFi board's ESP32-S3 link are separate paths.

[1] [3]
DIGITAL.2D1Arduino D1 · MCU port P302General-purpose I/OSerial1 TX

Header Serial1 connects to the RA4M1 SCI2 peripheral. USB Serial and the WiFi board's ESP32-S3 link are separate paths.

[1] [3]
DIGITAL.3D2Arduino D2 · MCU port P105General-purpose I/O——[1] [3]
DIGITAL.4D3Arduino D3 · MCU port P104General-purpose I/OPWM—[1] [3]
DIGITAL.5D4Arduino D4 · MCU port P103General-purpose I/OCAN0 TX—[1] [3]
DIGITAL.6D5Arduino D5 · MCU port P102General-purpose I/OPWMCAN0 RX—[1] [3]
DIGITAL.7D6Arduino D6 · MCU port P106General-purpose I/OPWM—[1] [3]
DIGITAL.8D7Arduino D7 · MCU port P107General-purpose I/O——[1] [3]
DIGITAL.9D8Arduino D8 · MCU port P304General-purpose I/O——[1] [3]
DIGITAL.10D9Arduino D9 · MCU port P303General-purpose I/OPWM—[1] [3]
DIGITAL.11D10Arduino D10 · MCU port P112General-purpose I/OSPI SSPWM—[1] [3]
DIGITAL.12D11Arduino D11 · MCU port P109General-purpose I/OSPI COPI / MOSIPWM

Same electrical signal as ICSP.4

[1] [3]
DIGITAL.13D12Arduino D12 · MCU port P110General-purpose I/OSPI CIPO / MISO

Same electrical signal as ICSP.1

[1] [3]
DIGITAL.14D13Arduino D13 · MCU port P111General-purpose I/OSPI SCK

Same electrical signal as ICSP.3

[1] [3]
DIGITAL.15GNDGround——[1]
DIGITAL.16AREFSystem—

Analog reference input. Select the appropriate analogReference() mode before connecting an external reference; this is not a power output.

[1]
DIGITAL.17SDAArduino D18 · MCU port P101General-purpose I/OI2C SDAAN021

Same electrical signal as ANALOG.5

[1] [3]
DIGITAL.18SCLArduino D19 · MCU port P100General-purpose I/OI2C SCLAN022

Same electrical signal as ANALOG.6

[1] [3]
ICSP.5RESETSystem—

Same electrical signal as PWR.3

Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit.

[1]
ICSP.3SCKArduino D13 · MCU port P111General-purpose I/OSPI SCK

Same electrical signal as DIGITAL.14

[1] [3]
ICSP.1CIPOArduino D12 · MCU port P110General-purpose I/OSPI CIPO / MISO

Same electrical signal as DIGITAL.13

[1] [3]
ICSP.6GNDGround——[1]
ICSP.4COPIArduino D11 · MCU port P109General-purpose I/OSPI COPI / MOSIPWM

Same electrical signal as DIGITAL.12

[1] [3]
ICSP.25VPower——[1]

General usage notes

RA4M1 5 V I/O. Observe 8 mA per-pin and 60 mA total limits. CAN needs an external transceiver. Configure timers and peripherals for the selected R4 model.

Model-specific features and connection notes

Sources

Pin and warning references

  1. Arduino uno-r4-minima full pinout · PDF p. 1Main headers · USB at top · recorded connector positions, signal labels and optional SPI/ICSP connector
  2. Arduino uno-r4-minima datasheetConnector pinouts · IOREF: reference for digital logic V, connected to 5 V
  3. Arduino Renesas core · variants/MINIMA/variant.cppg_pin_cfg · RA4M1 port map; initVariant · six Arduino PWM channels

Technical sources (3)

  1. uno-r4-minima hardware manualArduino · Tech specs; downloadable datasheet and schematic
  2. ABX00080 circuit schematicArduino · Complete board circuit
  3. UNO R4 availableArduino · Publication date / availability

Locked source documents

Pin reference · Datasheet