Development boards
Arduino Nano Every pinout
ATmega4809 · 16 MHz · 5 V I/O
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
USB at top. 30 side contacts and 22 independent GPIOs; A6/A7 also support digital I/O. Arduino PWM uses D3/D5/D6/D9/D10; D11 has no Arduino PWM support. A4 and A5 connect PF2/PA2 and PF3/PA3 respectively; coordinate I²C and ADC/GPIO drivers. Underside SAMD11/UPDI debug pads are outside this map.
At a glance
- Platform / manufacturer
- Arduino
- Type
- Development boards
- MCU
- ATmega4809
- Physical contacts
- 30
- GPIO
- 22
- I/O voltage
- 5 V I/O
- Interfaces (pin count)
- I²C (2) · SPI (4) · UART (2) · ADC (8) · PWM (5) · IRQ (22)
- Announcement date
- 2019-05-17 [c]
- MCU / processor core
- 8-bit AVR [a]
- Internal RAM / system RAM
- 6 KB SRAM [a]
- Program Flash / storage
- 48 KB Flash [a]
- EEPROM / persistent data
- 256 B EEPROM [a]
- Pin sources checked
- 2026-11-05
- Technical details reviewed
- 2026-11-14
All pins (30)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| L.1 | D13Arduino D13 · MCU port PE2 | General-purpose I/O | SPI SCKGPIO interrupt | — | [1] [2] |
| L.2 | 3V3 | Power | — | — | [1] |
| L.3 | AREF | System | — | Analog reference input. Select the appropriate analogReference() mode before connecting an external reference; this is not a power output. | [1] |
| L.4 | A0Arduino D14 · MCU port PD3 | General-purpose I/O | ADC3GPIO interrupt | — | [1] [2] |
| L.5 | A1Arduino D15 · MCU port PD2 | General-purpose I/O | ADC2GPIO interrupt | — | [1] [2] |
| L.6 | A2Arduino D16 · MCU port PD1 | General-purpose I/O | ADC1GPIO interrupt | — | [1] [2] |
| L.7 | A3Arduino D17 · MCU port PD0 | General-purpose I/O | ADC0GPIO interrupt | — | [1] [2] |
| L.8 | A4Arduino D18 · MCU port PF2 / PA2 | General-purpose I/O | I2C SDAADC12GPIO interrupt | This contact connects two MCU pins: ADC/GPIO and TWI share the physical connection. Keep the other GPIO driver high-impedance when using I²C; do not use ADC and I²C on the signal simultaneously. | [1] [2] |
| L.9 | A5Arduino D19 · MCU port PF3 / PA3 | General-purpose I/O | I2C SCLADC13GPIO interrupt | This contact connects two MCU pins: ADC/GPIO and TWI share the physical connection. Keep the other GPIO driver high-impedance when using I²C; do not use ADC and I²C on the signal simultaneously. | [1] [2] |
| L.10 | A6Arduino D20 · MCU port PD4 | General-purpose I/O | ADC4GPIO interrupt | — | [1] [2] |
| L.11 | A7Arduino D21 · MCU port PD5 | General-purpose I/O | ADC5GPIO interrupt | — | [1] [2] |
| L.12 | 5V | Power | — | — | [1] |
| L.13 | RESET | System | — | Same electrical signal as R.13 Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit. | [1] |
| L.14 | GND | Ground | — | — | [1] |
| L.15 | VIN | Power | — | Unregulated power input, not GPIO. Check the board datasheet for the input range and regulator thermal limits. | [1] |
| R.1 | D12Arduino D12 · MCU port PE1 | General-purpose I/O | SPI CIPO / MISOGPIO interrupt | — | [1] [2] |
| R.2 | D11Arduino D11 · MCU port PE0 | General-purpose I/O | SPI COPI / MOSIGPIO interrupt | — | [1] [2] |
| R.3 | D10Arduino D10 · MCU port PB1 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.4 | D9Arduino D9 · MCU port PB0 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.5 | D8Arduino D8 · MCU port PE3 | General-purpose I/O | SPI SSGPIO interrupt | — | [1] [2] |
| R.6 | D7Arduino D7 · MCU port PA1 | General-purpose I/O | GPIO interrupt | — | [1] [2] |
| R.7 | D6Arduino D6 · MCU port PF4 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.8 | D5Arduino D5 · MCU port PB2 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.9 | D4Arduino D4 · MCU port PC6 | General-purpose I/O | GPIO interrupt | — | [1] [2] |
| R.10 | D3Arduino D3 · MCU port PF5 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.11 | D2Arduino D2 · MCU port PA0 | General-purpose I/O | GPIO interrupt | — | [1] [2] |
| R.12 | GND | Ground | — | — | [1] |
| R.13 | RESET | System | — | Same electrical signal as L.13 Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit. | [1] |
| R.14 | D0Arduino D0 · MCU port PC5 | General-purpose I/O | Serial1 RXGPIO interrupt | Serial1 on D0/D1 uses the ATmega4809 USART1 alternate pins. The USB serial bridge uses different MCU pins. | [1] [2] |
| R.15 | D1Arduino D1 · MCU port PC4 | General-purpose I/O | Serial1 TXGPIO interrupt | Serial1 on D0/D1 uses the ATmega4809 USART1 alternate pins. The USB serial bridge uses different MCU pins. | [1] [2] |
General usage notes
5 V logic. Arduino's board guidance specifies 20 mA per I/O; port and total MCU current limits also apply. PWM is not a true analog voltage output. Coordinate timer and peripheral use in firmware.
Model-specific features and connection notes
- ATmega4809: 48 KB Flash, 6 KB SRAM and 256 B EEPROM. USB bridge is SAMD11; it does not use the Nano Classic AVR register map. [a]
Sources
Pin and warning references
- Arduino nano-every full pinout · PDF p. 1Main headers · USB at top · recorded connector positions, signal labels and optional SPI/ICSP connector
- Arduino official core · variants/nona4809/pins_arduino.hOfficial core · Arduino pin aliases, MCU port map, analog channels, SPI/Wire and supported PWM outputs
Technical sources (3)
- nano-every hardware manualArduino · Tech specs; downloadable datasheet and schematic
- ABX00028 circuit schematicArduino · Complete board circuit
- arduino-nano-every announcementArduino · Publication date
Locked source documents
- Arduino nano-every full pinoutArduino · 2021-12-15 · arduino/docs-content · cb938e96b391e636011690e4db1348dc38db4deb
- Arduino official core · variants/nona4809/pins_arduino.hArduino · e8edb4ef2e8ab5c98544c3884a653f0b9c1318dc