Development boards

Arduino Micro pinout

ATmega32U4 · 16 MHz · 5 V I/O

Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe

USB at top. 34 side-header and 6 ICSP contacts; 24 independent GPIOs. This is a separate footprint from Nano. CIPO/SCK/SS/COPI occupy extra side contacts; ICSP repeats three of them. I²C uses D2/D3 and 12 ADC inputs share several digital pins. USB Serial and D0/D1 Serial1 are separate.

At a glance

Platform / manufacturer
Arduino
Type
Development boards
MCU
ATmega32U4
Physical contacts
40
GPIO
24
I/O voltage
5 V I/O
Interfaces (pin count)
I²C (2) · SPI (7) · UART (2) · ADC (12) · PWM (7) · IRQ (5)
Initial sale / release date
2012-11-08 [d]
MCU / processor core
8-bit AVR [a]
Clock speed / maximum
16 MHz [b] [c]
Internal RAM / system RAM
2.5 KB SRAM [a]
Program Flash / storage
32 KB Flash [a]
EEPROM / persistent data
1 KB EEPROM [a]
Power and logic level
USB: 5 V; header GPIO: 5 V. See the board manual for VIN limits. [b] [c]
Pin sources checked
2026-11-05
Technical details reviewed
2026-11-14

All pins (40)

Arduino Micro: every pin in physical order with its type, functions and warnings
PhysicalPin nameTypeFunctionsNotes and warningsSource
L.1D13Arduino D13 · MCU port PC7General-purpose I/OPWM OC4A—[1] [2]
L.23V3Power——[1]
L.3AREFSystem—

Analog reference input. Select the appropriate analogReference() mode before connecting an external reference; this is not a power output.

[1]
L.4A0Arduino D18 · MCU port PF7General-purpose I/OADC7—[1] [2]
L.5A1Arduino D19 · MCU port PF6General-purpose I/OADC6—[1] [2]
L.6A2Arduino D20 · MCU port PF5General-purpose I/OADC5—[1] [2]
L.7A3Arduino D21 · MCU port PF4General-purpose I/OADC4—[1] [2]
L.8A4Arduino D22 · MCU port PF1General-purpose I/OADC1—[1] [2]
L.9A5Arduino D23 · MCU port PF0General-purpose I/OADC0—[1] [2]
L.10NCSystem—

Unconnected

Unconnected contact. Do not use as power or GPIO.

[1]
L.11NCSystem—

Unconnected

Unconnected contact. Do not use as power or GPIO.

[1]
L.125VPower——[1]
L.13RESETSystem—

Same electrical signal as R.13, ICSP.5

Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit.

[1]
L.14GNDGround——[1]
L.15VINPower—

Unregulated power input, not GPIO. Check the board datasheet for the input range and regulator thermal limits.

[1]
L.16CIPOArduino D14 · MCU port PB3General-purpose I/OSPI CIPO / MISO

Same electrical signal as ICSP.1

[1] [2]
L.17SCKArduino D15 · MCU port PB1General-purpose I/OSPI SCK

Same electrical signal as ICSP.3

[1] [2]
R.1D12Arduino D12 · MCU port PD6General-purpose I/OADC9—[1] [2]
R.2D11Arduino D11 · MCU port PB7General-purpose I/OPWM OC0A—[1] [2]
R.3D10Arduino D10 · MCU port PB6General-purpose I/OPWM OC1BADC13—[1] [2]
R.4D9Arduino D9 · MCU port PB5General-purpose I/OPWM OC1AADC12—[1] [2]
R.5D8Arduino D8 · MCU port PB4General-purpose I/OADC11—[1] [2]
R.6D7Arduino D7 · MCU port PE6General-purpose I/OINT6—[1] [2]
R.7D6Arduino D6 · MCU port PD7General-purpose I/OPWM OC4DADC10—[1] [2]
R.8D5Arduino D5 · MCU port PC6General-purpose I/OPWM OC3A—[1] [2]
R.9D4Arduino D4 · MCU port PD4General-purpose I/OADC8—[1] [2]
R.10D3Arduino D3 · MCU port PD0General-purpose I/OI2C SCLPWM OC0BINT0—[1] [2]
R.11D2Arduino D2 · MCU port PD1General-purpose I/OI2C SDAINT1—[1] [2]
R.12GNDGround——[1]
R.13RESETSystem—

Same electrical signal as L.13, ICSP.5

Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit.

[1]
R.14D0Arduino D0 · MCU port PD2General-purpose I/OSerial1 RXINT2

The ATmega32U4 hardware UART is Serial1. USB Serial uses the MCU's USB peripheral and is separate from D0/D1.

[1] [2]
R.15D1Arduino D1 · MCU port PD3General-purpose I/OSerial1 TXINT3

The ATmega32U4 hardware UART is Serial1. USB Serial uses the MCU's USB peripheral and is separate from D0/D1.

[1] [2]
R.16SSArduino D17 · MCU port PB0General-purpose I/OSPI SS—[1] [2]
R.17COPIArduino D16 · MCU port PB2General-purpose I/OSPI COPI / MOSI

Same electrical signal as ICSP.4

[1] [2]
ICSP.1CIPOArduino D14 · MCU port PB3General-purpose I/OSPI CIPO / MISO

Same electrical signal as L.16

[1] [2]
ICSP.25VPower——[1]
ICSP.3SCKArduino D15 · MCU port PB1General-purpose I/OSPI SCK

Same electrical signal as L.17

[1] [2]
ICSP.4COPIArduino D16 · MCU port PB2General-purpose I/OSPI COPI / MOSI

Same electrical signal as R.17

[1] [2]
ICSP.5RESETSystem—

Same electrical signal as L.13, R.13

Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit.

[1]
ICSP.6GNDGround——[1]

General usage notes

ATmega32U4 5 V I/O. Coordinate GPIO and peripheral modes; check the MCU datasheet for pin, port and total current limits. PWM is not a true analog output.

Model-specific features and connection notes

Sources

Pin and warning references

  1. Arduino micro full pinout · PDF p. 1Main headers · USB at top · recorded connector positions, signal labels and optional SPI/ICSP connector
  2. Arduino official core · variants/leonardo/pins_arduino.hOfficial core · Arduino pin aliases, MCU port map, analog channels, SPI/Wire and supported PWM outputs

Technical sources (4)

  1. leonardo hardware manualArduino · Tech specs; downloadable datasheet and schematic
  2. micro hardware manualArduino · Tech specs; downloadable datasheet and schematic
  3. A000053 circuit schematicArduino · Complete board circuit
  4. arduino-micro announcementArduino · Publication date

Locked source documents

Pin reference · Datasheet