Development boards
Arduino Nano 33 BLE Sense Rev2 pinout
nRF52840 · 64 MHz · 3.3 V I/O · BLE + Sensors
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
USB at top. 30 side contacts and 22 independent GPIOs; all digital pins support PWM. Warning: 3.3 V I/O only; NOT 5 V tolerant. Onboard sensors include BMI270 (6-axis IMU), BMM150 (3-axis magnetometer), LPS22HB (barometer), APDS-9960 (gesture/proximity/light), HS3003 (humidity/temp) and MP34DT06JTR (microphone). D1/RX and D0/TX are inverted relative to classic Nano.
At a glance
- Platform / manufacturer
- Arduino
- Type
- Development boards
- MCU
- nRF52840
- Physical contacts
- 30
- GPIO
- 22
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (2) · SPI (4) · UART (2) · ADC (8) · PWM (14) · IRQ (22)
- MCU / processor core
- Arm Cortex-M4F [a]
- Internal RAM / system RAM
- 256 KB SRAM [a]
- Program Flash / storage
- 1 MB Flash [a]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
All pins (30)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| L.1 | D13Arduino D13 · MCU port P0.13 | General-purpose I/O | SPI SCKPWMGPIO interrupt | — | [1] [2] |
| L.2 | 3V3 | Power | — | — | [1] |
| L.3 | AREF | System | — | Analog reference input. Select the appropriate analogReference() mode before connecting an external reference; this is not a power output. | [1] |
| L.4 | A0Arduino D14 · MCU port P0.04 | General-purpose I/O | AIN2GPIO interrupt | — | [1] [2] |
| L.5 | A1Arduino D15 · MCU port P0.05 | General-purpose I/O | AIN3GPIO interrupt | — | [1] [2] |
| L.6 | A2Arduino D16 · MCU port P0.30 | General-purpose I/O | AIN6GPIO interrupt | — | [1] [2] |
| L.7 | A3Arduino D17 · MCU port P0.29 | General-purpose I/O | AIN5GPIO interrupt | — | [1] [2] |
| L.8 | A4Arduino D18 · MCU port P0.31 | General-purpose I/O | I2C SDAAIN7GPIO interrupt | — | [1] [2] |
| L.9 | A5Arduino D19 · MCU port P0.02 | General-purpose I/O | I2C SCLAIN0GPIO interrupt | — | [1] [2] |
| L.10 | A6Arduino D20 · MCU port P0.28 | General-purpose I/O | AIN4GPIO interrupt | — | [1] [2] |
| L.11 | A7Arduino D21 · MCU port P0.03 | General-purpose I/O | AIN1GPIO interrupt | — | [1] [2] |
| L.12 | 5V | Power | — | Unconnected by default. Closing solder jumper SJ1 on the bottom of the board (SJ5 is a parallel pad pair) connects USB VBUS (5 V) to this contact. Source: [3] | [1] [3] |
| L.13 | RESET | System | — | Same electrical signal as R.13 Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit. | [1] |
| L.14 | GND | Ground | — | — | [1] |
| L.15 | VIN | Power | — | Unregulated power input, not GPIO. Check the board datasheet for the input range and regulator thermal limits. | [1] |
| R.1 | D12Arduino D12 · MCU port P1.08 | General-purpose I/O | SPI CIPO / MISOPWMGPIO interrupt | — | [1] [2] |
| R.2 | D11Arduino D11 · MCU port P1.01 | General-purpose I/O | SPI COPI / MOSIPWMGPIO interrupt | — | [1] [2] |
| R.3 | D10Arduino D10 · MCU port P1.02 | General-purpose I/O | SPI SSPWMGPIO interrupt | — | [1] [2] |
| R.4 | D9Arduino D9 · MCU port P0.27 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.5 | D8Arduino D8 · MCU port P0.21 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.6 | D7Arduino D7 · MCU port P0.23 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.7 | D6Arduino D6 · MCU port P1.14 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.8 | D5Arduino D5 · MCU port P1.13 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.9 | D4Arduino D4 · MCU port P1.15 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.10 | D3Arduino D3 · MCU port P1.12 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.11 | D2Arduino D2 · MCU port P1.11 | General-purpose I/O | PWMGPIO interrupt | — | [1] [2] |
| R.12 | GND | Ground | — | — | [1] |
| R.13 | RESET | System | — | Same electrical signal as L.13 Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit. | [1] |
| R.14 | D1Arduino D1 · MCU port P1.10 | General-purpose I/O | Serial1 RXPWMGPIO interrupt | — | [1] [2] |
| R.15 | D0Arduino D0 · MCU port P1.03 | General-purpose I/O | Serial1 TXPWMGPIO interrupt | — | [1] [2] |
General usage notes
3.3 V I/O logic level. nRF52840 pins are NOT 5 V tolerant; applying >3.3 V permanently damages the MCU. All GPIOs support hardware/software PWM and pin-change interrupts.
Model-specific features and connection notes
- NINA-B306/nRF52840: BLE, native USB and sensors. Rev2 IMU: BMI270 + BMM150; temperature/humidity: HS3003. GPIO is not 5 V tolerant. [a]
Sources
Pin and warning references
- Arduino Nano 33 BLE Sense Rev2 full pinout · PDF p. 1Main headers · USB at top · recorded connector positions, signal labels and optional SPI/ICSP connector
- Arduino mbed core · variants/ARDUINO_NANO33BLE/variant.cppPinDescription g_APinDescription · nRF52840 port map and sensor interfaces
- Arduino Nano 33 BLE Sense Rev2 schematic · PDF p. 1Sheet 1 · SJ1/SJ5 between VUSB and the header 5V contact · note "SJ1 on BOTTOM"
Technical sources (2)
- nano-33-ble-sense-rev2 hardware manualArduino · Tech specs; downloadable datasheet and schematic
- ABX00069 circuit schematicArduino · Complete board circuit
Locked source documents
- Arduino Nano 33 BLE Sense Rev2 full pinoutArduino · 2022-12-22 · arduino/docs-content · cb938e96b391e636011690e4db1348dc38db4deb
- Arduino Nano 33 BLE Sense Rev2 schematicArduino · Rev2 · arduino/docs-content · cb938e96b391e636011690e4db1348dc38db4deb
- Arduino mbed core · variants/ARDUINO_NANO33BLE/variant.cppArduino · b4ad4e7218a691989acf6c4479112eae183a5a50