Development boards
Arduino Nano ESP32 pinout
ESP32-S3 (NORA-W106) · 240 MHz · 3.3 V I/O · Wi-Fi + BLE
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
USB-C at top. 30 side contacts and 24 independent GPIOs. 3.3 V I/O logic level (NOT 5 V tolerant). B0 (GPIO46) and B1 (GPIO0) are strapping/boot pins. All GPIOs support PWM and interrupts.
At a glance
- Platform / manufacturer
- Arduino
- Type
- Development boards
- MCU
- ESP32-S3
- Physical contacts
- 30
- GPIO
- 24
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (2) · SPI (4) · UART (4) · ADC (16) · PWM (24) · IRQ (24)
- Announcement date
- 2023-07-17 [d]
- MCU / processor core
- 2 × Xtensa LX7 [a]
- Internal RAM / system RAM
- 512 KB SRAM + 16 KB RTC SRAM [a]
- Fixed ROM / boot ROM
- 384 KB ROM [a]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
Cautions for this board
All pins (30)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| L.1 | D13Arduino D13 · MCU port GPIO48 | General-purpose I/O | SPI SCKPWMGPIO interrupt | — | [3] [4] |
| L.2 | 3V3 | Power | — | — | [3] [5] |
| L.3 | B0Arduino D14 · MCU port GPIO46 | General-purpose I/O | PWMGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. Source: [1] B0 pin is connected to GPIO46 and the Red LED. Boot/strapping pin: level at reset may affect boot mode. Source: [2] [1] | [3] [4] [1] [2] |
| L.4 | A0Arduino D17 · MCU port GPIO1 | General-purpose I/O | ADC1_CH0PWMGPIO interrupt | — | [3] [4] |
| L.5 | A1Arduino D18 · MCU port GPIO2 | General-purpose I/O | ADC1_CH1PWMGPIO interrupt | — | [3] [4] |
| L.6 | A2Arduino D19 · MCU port GPIO3 | General-purpose I/O | ADC1_CH2PWMGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. Source: [1] | [3] [4] [1] [2] |
| L.7 | A3Arduino D20 · MCU port GPIO4 | General-purpose I/O | ADC1_CH3PWMGPIO interrupt | — | [3] [4] |
| L.8 | A4Arduino D21 · MCU port GPIO11 | General-purpose I/O | I2C SDAADC2_CH0PWMGPIO interrupt | — | [3] [4] |
| L.9 | A5Arduino D22 · MCU port GPIO12 | General-purpose I/O | I2C SCLADC2_CH1PWMGPIO interrupt | — | [3] [4] |
| L.10 | A6Arduino D23 · MCU port GPIO13 | General-purpose I/O | ADC2_CH2PWMGPIO interrupt | — | [3] [4] |
| L.11 | A7Arduino D24 · MCU port GPIO14 | General-purpose I/O | ADC2_CH3PWMGPIO interrupt | — | [3] [4] |
| L.12 | VUSB | Power | — | USB VBUS 5 V power rail. Supplies 5 V when the board is powered via USB. | [3] [5] |
| L.13 | B1Arduino D15 · MCU port GPIO0 | General-purpose I/O | PWMGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. Source: [1] B1 is connected to GPIO0 and the green LED; its Arduino pin number is 15 (LED_GREEN). Number 16 is the blue LED on GPIO45. Strapping pin: pulling it LOW at reset enters ROM download mode. Source: [2] [1] | [3] [4] [1] [2] |
| L.14 | GND | Ground | — | — | [3] [5] |
| L.15 | VIN | Power | — | Unregulated power input, not GPIO. Check the board datasheet for the input range and regulator thermal limits. | [3] [5] |
| R.1 | D12Arduino D12 · MCU port GPIO47 | General-purpose I/O | SPI CIPO / MISOPWMGPIO interrupt | — | [3] [4] |
| R.2 | D11Arduino D11 · MCU port GPIO38 | General-purpose I/O | SPI COPI / MOSIPWMGPIO interrupt | — | [3] [4] |
| R.3 | D10Arduino D10 · MCU port GPIO21 | General-purpose I/O | SPI SSPWMGPIO interrupt | — | [3] [4] |
| R.4 | D9Arduino D9 · MCU port GPIO18 | General-purpose I/O | Serial1 RXADC2_CH7PWMGPIO interrupt | — | [3] [4] |
| R.5 | D8Arduino D8 · MCU port GPIO17 | General-purpose I/O | Serial1 TXADC2_CH6PWMGPIO interrupt | — | [3] [4] |
| R.6 | D7Arduino D7 · MCU port GPIO10 | General-purpose I/O | ADC1_CH9PWMGPIO interrupt | — | [3] [4] |
| R.7 | D6Arduino D6 · MCU port GPIO9 | General-purpose I/O | ADC1_CH8PWMGPIO interrupt | — | [3] [4] |
| R.8 | D5Arduino D5 · MCU port GPIO8 | General-purpose I/O | ADC1_CH7PWMGPIO interrupt | — | [3] [4] |
| R.9 | D4Arduino D4 · MCU port GPIO7 | General-purpose I/O | ADC1_CH6PWMGPIO interrupt | — | [3] [4] |
| R.10 | D3Arduino D3 · MCU port GPIO6 | General-purpose I/O | ADC1_CH5PWMGPIO interrupt | — | [3] [4] |
| R.11 | D2Arduino D2 · MCU port GPIO5 | General-purpose I/O | ADC1_CH4PWMGPIO interrupt | — | [3] [4] |
| R.12 | GND | Ground | — | — | [3] [5] |
| R.13 | RESET | System | — | Active-low MCU reset. Shared with the reset button, ICSP and auto-reset circuit. | [3] [5] |
| R.14 | D0Arduino D0 · MCU port GPIO44 | General-purpose I/O | Serial0 RXPWMGPIO interrupt | D0 (RX0 / GPIO44) and D1 (TX0 / GPIO43) are the hardware Serial0 port. D1/TX0 has a 499 Ω series resistor. | [3] [4] |
| R.15 | D1Arduino D1 · MCU port GPIO43 | General-purpose I/O | Serial0 TXPWMGPIO interrupt | D0 (RX0 / GPIO44) and D1 (TX0 / GPIO43) are the hardware Serial0 port. D1/TX0 has a 499 Ω series resistor. | [3] [4] |
General usage notes
3.3 V I/O level. ESP32-S3 pins are NOT 5 V tolerant; voltages above 3.3 V will damage the chip.
Model-specific features and connection notes
- u-blox NORA-W106 / ESP32-S3. Arduino D labels differ from ESP32 GPIO numbers; match Tools > Pin Numbering to your code. [b]
Sources
Pin and warning references
- ESP32S3 series datasheet · PDF p. 32§3 Boot Configurations · strapping pins GPIO0, GPIO3, GPIO45 and GPIO46
- Arduino Nano ESP32 core pin definitions (pins_arduino.h)pins_arduino.h · LED_RED = 14 (GPIO46), LED_GREEN = 15 (GPIO0), LED_BLUE = 16 (GPIO45), A2 = 19 (GPIO3)
- Arduino Nano ESP32 full pinout · PDF p. 1Main headers · USB-C at top · connector positions, digital and analog pinout
- Arduino Nano ESP32 full pinout · PDF p. 3Advanced Section · ESP32-S3 GPIO mappings, ADC channels, and secondary UART
- Arduino Nano ESP32 schematic · PDF p. 1Sheet 1/2 · JP1/JP2 header connections, power rails, and strapping pins
Technical sources (5)
- ESP32S3 series datasheetEspressif · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- nano-esp32 hardware manualArduino · Tech specs; downloadable datasheet and schematic
- ABX00083 circuit schematicArduino · Complete board circuit
- arduino-nano-esp32 announcementArduino · Publication date
- Arduino Nano ESP32 schematicArduino · Locked pin-source document; see sources/manifest.json for revision and SHA-256
Locked source documents
- Arduino Nano ESP32 full pinoutArduino · 2024-04-18 · arduino/docs-content · cb938e96b391e636011690e4db1348dc38db4deb
- Arduino Nano ESP32 schematicArduino · v1.1 · arduino/docs-content · cb938e96b391e636011690e4db1348dc38db4deb
- ESP32S3 series datasheetEspressif · Snapshot reviewed 2026-11-04
- Arduino Nano ESP32 core pin definitions (pins_arduino.h)Espressif / Arduino · 6bfcd6d9a9a7ecd07d656a7a88673c93e7d4d537