Development boards
NodeMCU v2 pinout
ESP8266EX · Tensilica L106 · 80 MHz · Wi-Fi · 3.3 V I/O
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
At a glance
- Platform / manufacturer
- Espressif
- Type
- Development boards
- MCU
- ESP8266EX
- Package / connector
- 30-pin DIP module
- Physical contacts
- 30
- GPIO
- 17 (6 reserved)
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (2) · SPI (10) · UART (5) · ADC (1) · PWM (10) · IRQ (11) · SYSTEM (2)
- Initial sale / release date
- 2015-01-29 [d]
- MCU / processor core
- 1 × Tensilica L106 32-bit [a]
- Clock speed / maximum
- 80 MHz (160 MHz max) [a]
- Internal RAM / system RAM
- 80 KB user data SRAM + 32 KB instruction RAM + 32 KB instruction cache [a]
- Power and logic level
- Micro-USB: 5 V; VIN: 4.5–9 V; GPIO: 3.3 V. A 5 V power pin does not imply 5 V GPIO tolerance. [b] [c] [a]
- Pin sources checked
- 2026-11-16
- Technical details reviewed
- 2026-11-14
All pins (30)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| J1.1 | A0 | Analog | ADC0 | Single 10-bit analog input (TOUT). The board includes an onboard 220 kΩ / 100 kΩ voltage divider, accepting 0–3.3 V inputs. | [1] [2] |
| J1.2 | RSV | System | — | RSV No connection (unconnected pin). Do not connect to external circuitry. | [1] |
| J1.3 | RSV | System | — | RSV No connection (unconnected pin). Do not connect to external circuitry. | [1] |
| J1.4 | SD3 | General-purpose I/O | SDIO_D3 | SD3 Connected to internal SPI Flash memory lines (GPIO6–GPIO11). Do NOT use for external circuits; accessing these pins causes crashes. | [1] [2] |
| J1.5 | SD2 | General-purpose I/O | SDIO_D2 | SD2 Connected to internal SPI Flash memory lines (GPIO6–GPIO11). Do NOT use for external circuits; accessing these pins causes crashes. | [1] [2] |
| J1.6 | SD1 | General-purpose I/O | SDIO_D1 | SD1 Connected to internal SPI Flash memory lines (GPIO6–GPIO11). Do NOT use for external circuits; accessing these pins causes crashes. | [1] [2] |
| J1.7 | CMD | General-purpose I/O | SDIO_CMD | CMD Connected to internal SPI Flash memory lines (GPIO6–GPIO11). Do NOT use for external circuits; accessing these pins causes crashes. | [1] [2] |
| J1.8 | SD0 | General-purpose I/O | SDIO_D0 | SD0 Connected to internal SPI Flash memory lines (GPIO6–GPIO11). Do NOT use for external circuits; accessing these pins causes crashes. | [1] [2] |
| J1.9 | CLK | General-purpose I/O | SDIO_CLK | CLK Connected to internal SPI Flash memory lines (GPIO6–GPIO11). Do NOT use for external circuits; accessing these pins causes crashes. | [1] [2] |
| J1.10 | GND | Ground | — | — | [1] |
| J1.11 | 3V3 | Power | — | — | [1] |
| J1.12 | EN | System | — | CHIP_PU/EN reset-enable input, not a normal GPIO. Shared with the board's reset circuit. | [1] |
| J1.13 | RST | System | — | Active-low hardware reset (EXT_RSTB) pin. Connected to the onboard RST push button. | [1] |
| J1.14 | GND | Ground | — | — | [1] |
| J1.15 | VIN | Power | — | External 5 V power input (feeds the onboard 3.3 V regulator). Exercise caution when USB and external power are connected. | [1] |
| J2.1 | D0 | General-purpose I/O | WAKEGPIO interrupt | Deep-sleep wake-up pin (XPD_DCDC). Connect to the RST pin so the chip can reset itself upon waking from deep sleep. | [1] [2] |
| J2.2 | D1 | General-purpose I/O | I2C SCLPWMGPIO interrupt | — | [1] [2] |
| J2.3 | D2 | General-purpose I/O | I2C SDAPWMGPIO interrupt | — | [1] [2] |
| J2.4 | D3 | General-purpose I/O | FLASH buttonPWMGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. Boot strapping pin (GPIO0). Must be HIGH for normal boot. Pressing the onboard FLASH button pulls it LOW to enter UART download mode. | [1] [2] [3] |
| J2.5 | D4 | General-purpose I/O | UART1 TXPWMGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. Boot strapping pin (GPIO2) and UART1 TX. Must be HIGH during boot. Connected to the onboard blue LED (active-LOW logic). | [1] [2] [3] |
| J2.6 | 3V3 | Power | — | — | [1] |
| J2.7 | GND | Ground | — | — | [1] |
| J2.8 | D5 | General-purpose I/O | HSPI SCKPWMGPIO interrupt | — | [1] [2] |
| J2.9 | D6 | General-purpose I/O | HSPI MISOPWMGPIO interrupt | — | [1] [2] |
| J2.10 | D7 | General-purpose I/O | HSPI MOSIUART0 CTSPWMGPIO interrupt | — | [1] [2] |
| J2.11 | D8 | General-purpose I/O | HSPI CSUART0 RTSPWMGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. Boot strapping pin (GPIO15 / MTDO). Must be LOW for normal boot (pulled to GND with an onboard 12 kΩ resistor). | [1] [2] [3] |
| J2.12 | RX | General-purpose I/O | UART0 RXPWMGPIO interrupt | Hardware UART0 serial communication port (TXD0/RXD0). Connected to the onboard USB-UART bridge (CP2102/CH340). | [1] [2] |
| J2.13 | TX | General-purpose I/O | UART0 TXPWMGPIO interrupt | Hardware UART0 serial communication port (TXD0/RXD0). Connected to the onboard USB-UART bridge (CP2102/CH340). | [1] [2] |
| J2.14 | GND | Ground | — | — | [1] |
| J2.15 | 3V3 | Power | — | — | [1] |
General usage notes
3.3 V I/O; do not apply 5 V. Matrix choices need SDK pin routing and peripheral configuration. I²C requires open-drain operation and suitable pull-ups.
Model-specific features and connection notes
Sources
Pin and warning references
- NodeMCU DEVKIT v1.0 Schematic · PDF p. 5Sheet 5/9 · connectors J1 (A0–VIN) and J2 (D0–3V3)
- ESP8266EX Datasheet · PDF p. 10Table 2-1 · ESP8266EX Pin Definitions · pin multiplexing and HSPI/UART assignments
- ESP8266EX Datasheet · PDF p. 11§2 · Pin Definitions · Note on strapping: GPIO2, GPIO0, MTDO/GPIO15 boot mode selection
Technical sources (4)
- ESP8266EX DatasheetEspressif Systems · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- NodeMCU DEVKIT v1.0 specificationsNodeMCU · Repository README, hardware schematic and specifications
- NodeMCU DEVKIT v1.0 SchematicNodeMCU · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- NodeMCU DevKit release historyNodeMCU · First release tag 2015-01-29
Locked source documents
- NodeMCU DEVKIT v1.0 SchematicNodeMCU · DevKit v1.0
- ESP8266EX DatasheetEspressif Systems · v7.1 · 2025-11