Development boards
Seeed Studio XIAO ESP32C3 pinout
ESP32-C3 · RISC-V · 160 MHz · Wi-Fi + BLE · 3.3 V I/O
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
At a glance
- Platform / manufacturer
- Seeed Studio
- Type
- Development boards
- MCU
- ESP32-C3
- Package / connector
- 14-contact header
- Physical contacts
- 14
- GPIO
- 11
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (11) · SPI (11) · UART (11) · ADC (4) · PWM (11) · IRQ (11) · JTAG (4)
- Initial sale / release date
- 2022-07-07 [d]
- MCU / processor core
- 1 × 32-bit RISC-V [a]
- Clock speed / maximum
- 160 MHz [a]
- Internal RAM / system RAM
- 400 KB SRAM (16 KB cache included) + 8 KB RTC SRAM [a]
- Fixed ROM / boot ROM
- 384 KB ROM [a]
- Power and logic level
- USB-C: 5 V; GPIO: 3.3 V. A 5 V power pin does not imply 5 V GPIO tolerance. [b] [c]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
All pins (14)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| L.1 | D0 | General-purpose I/O | ADC1_CH2FSPIQUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. | [1] [2] |
| L.2 | D1 | General-purpose I/O | ADC1_CH3UART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | — | [1] |
| L.3 | D2 | General-purpose I/O | ADC1_CH4FSPIHDMTMSUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | — | [1] |
| L.4 | D3 | General-purpose I/O | ADC2_CH0FSPIWPMTDIUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | On ESP32-C3, ADC2 is not factory-calibrated and is not operable on some chip revisions (see the ESP32-C3 Series SoC Errata). Prefer an ADC1 channel. Source: [3] | [1] [3] |
| L.5 | D4 | General-purpose I/O | FSPICLKMTCKUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | — | [1] |
| L.6 | D5 | General-purpose I/O | FSPIDMTDOUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | — | [1] |
| L.7 | D6 | General-purpose I/O | U0TXDUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | UART0 (U0TXD/U0RXD). This board has no USB-UART bridge: USB goes directly to the ESP32-C3’s native USB pins. Source: [1] | [1] |
| R.1 | 5V | Power | — | — | [1] |
| R.2 | GND | Ground | — | — | [1] |
| R.3 | 3V3 | Power | — | — | [1] |
| R.4 | D10 | General-purpose I/O | FSPICS0UART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | — | [1] |
| R.5 | D9 | General-purpose I/O | UART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | The on-board BOOT button is wired to this pin (GPIO9, a boot-mode strapping pin). Make sure external circuits do not pull the line LOW at power-up. Source: [1] [2] Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. | [1] [2] |
| R.6 | D8 | General-purpose I/O | UART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | Strapping pin: its reset-time level affects boot or hardware configuration. Check that external circuitry preserves the required reset levels. | [1] [2] |
| R.7 | D7 | General-purpose I/O | U0RXDUART1 RX (matrix) GPIO matrixUART1 TX (matrix) GPIO matrixSPI2 MISO (matrix) GPIO matrixSPI2 MOSI (matrix) GPIO matrixSPI2 SCK (matrix) GPIO matrixSPI2 CS (matrix) GPIO matrixI2C0 SDA (matrix) GPIO matrixI2C0 SCL (matrix) GPIO matrixLEDC PWM (matrix) GPIO matrixGPIO interrupt | UART0 (U0TXD/U0RXD). This board has no USB-UART bridge: USB goes directly to the ESP32-C3’s native USB pins. Source: [1] | [1] |
General usage notes
3.3 V I/O; do not apply 5 V. Matrix choices need SDK pin routing and peripheral configuration. I²C requires open-drain operation and suitable pull-ups.
Model-specific features and connection notes
- Standard 14-contact XIAO: 11 GPIO + 3 power/ground contacts. Do not apply Plus-variant extra pins to this map. [b]
Sources
Pin and warning references
- Seeed Studio XIAO ESP32C3 Schematic · PDF p. 3Sheet 3/3 · connectors J2 (D0–D6) and J1 (D7–D10, 3V3, GND, 5V)
- ESP32C3 series datasheet · PDF p. 30Boot configurations · strapping levels sampled during reset
- ESP32C3 series datasheet · PDF p. 49§4.2.2.1 SAR ADC · note: ADC2 of some chip revisions is not operable; ADC2 is not factory-calibrated
Technical sources (4)
- ESP32C3 series datasheetEspressif · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- XIAO ESP32C3 specificationsSeeed Studio · Features; specifications; resources
- Seeed Studio XIAO ESP32C3 SchematicSeeed Studio · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- XIAO ESP32C3 launchSeeed Studio · Explicit launch date in first paragraph
Locked source documents
- ESP32C3 series datasheetEspressif · Snapshot reviewed 2026-11-04
- Seeed Studio XIAO ESP32C3 SchematicSeeed Studio · v1.3 · 2026-01-15