Development boards
BBC micro:bit V2 pinout
nRF52833 · Cortex-M4F · 64 MHz · 3.3 V I/O
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
The front has 25 strips; physical order from the P3 end: P3, P0 (ring), P4, P5, P6, P7, P1 (ring), P8, P9, P10, P11, P12, P2 (ring), P13, P14, P15, P16, 3V (strip, ring, strip), P19, P20, GND (strip, ring, strip). Only the front strips carry signals. Pin IDs of previously saved plans are unchanged.
At a glance
- Platform / manufacturer
- BBC micro:bit
- Type
- Development boards
- MCU
- nRF52833
- Package / connector
- Edge connector · 25 front strips
- Physical contacts
- 25
- GPIO
- 19
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (2) · SPI (3) · UART (19) · ADC (6) · PWM (19) · SYSTEM (10) · TOUCH (3)
- Announcement date
- 2020-10-13 [c]
- MCU / processor core
- Arm Cortex-M4F [a]
- Clock speed / maximum
- 64 MHz [a]
- Internal RAM / system RAM
- 128 KB SRAM [a]
- Program Flash / storage
- 512 KB Flash [a]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
Cautions for this board
- The V2 on-board regulator can source 300 mA. The manufacturer’s power page gives both 270 mA and 190 mA as the budget for circuits on the edge connector; plan for the lower figure and power larger loads externally. Source: [1]
All pins (25)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| RING.0 | P0Board label 0 | General-purpose I/O | AIN0TOUCHPWMUART | — | [2] [3] |
| RING.1 | P1Board label 1 | General-purpose I/O | AIN1TOUCHPWMUART | — | [2] [3] |
| RING.2 | P2Board label 2 | General-purpose I/O | AIN2TOUCHPWMUART | — | [2] [3] |
| EDGE.3 | P3 | General-purpose I/O | AIN7LED_COL3PWMUART | Shared with 5×5 LED matrix column line. | [2] [3] |
| EDGE.4 | P4 | General-purpose I/O | AIN4LED_COL1PWMUART | Shared with 5×5 LED matrix column line. | [2] [3] |
| EDGE.5 | P5 | General-purpose I/O | BUTTON_APWMUART | Shared with on-board Button A and 10 kΩ pull-up. | [2] [3] |
| EDGE.6 | P6 | General-purpose I/O | LED_COL4PWMUART | Shared with 5×5 LED matrix column line. | [2] [3] |
| EDGE.7 | P7 | General-purpose I/O | LED_COL2PWMUART | Shared with 5×5 LED matrix column line. | [2] [3] |
| EDGE.8 | P8 | General-purpose I/O | NFC2PWMUART | — | [2] [3] |
| EDGE.9 | P9 | General-purpose I/O | NFC1PWMUART | — | [2] [3] |
| EDGE.10 | P10 | General-purpose I/O | AIN6LED_COL5PWMUART | Shared with 5×5 LED matrix column line. | [2] [3] |
| RING.3V | 3V | Power | — | 3 V supply strip from the on-board regulator; see the board’s current-budget caution. Source: [1] | [2] [3] [1] |
| RING.GND | GND | Ground | — | — | [2] [3] |
| EDGE.11 | P11 | General-purpose I/O | BUTTON_BPWMUART | Shared with on-board Button B and 10 kΩ pull-up. | [2] [3] |
| EDGE.12 | P12 | General-purpose I/O | ACCESSIBILITYPWMUART | — | [2] [3] |
| EDGE.13 | P13 | General-purpose I/O | SPI_SCKPWMUART | — | [2] [3] |
| EDGE.14 | P14 | General-purpose I/O | SPI_MISOPWMUART | — | [2] [3] |
| EDGE.15 | P15 | General-purpose I/O | SPI_MOSIPWMUART | — | [2] [3] |
| EDGE.16 | P16 | General-purpose I/O | PWMUART | — | [2] [3] |
| EDGE.19 | P19 | General-purpose I/O | I2C_SCLPWMUART | External I²C bus (I2C EXT) with on-board 4.7 kΩ pull-ups. On V2 the motion sensor is on a separate internal I²C bus, not on these pins. Source: [3] [4] | [2] [3] [4] |
| EDGE.20 | P20 | General-purpose I/O | I2C_SDAPWMUART | External I²C bus (I2C EXT) with on-board 4.7 kΩ pull-ups. On V2 the motion sensor is on a separate internal I²C bus, not on these pins. Source: [3] [4] | [2] [3] [4] |
| EDGE.3V.A | 3V | Power | — | 3 V supply strip from the on-board regulator; see the board’s current-budget caution. Source: [1] | [2] [3] [1] |
| EDGE.3V.B | 3V | Power | — | 3 V supply strip from the on-board regulator; see the board’s current-budget caution. Source: [1] | [2] [3] [1] |
| EDGE.GND.A | GND | Ground | — | — | [2] [3] |
| EDGE.GND.B | GND | Ground | — | — | [2] [3] |
Model-specific features and connection notes
- LED matrix, buttons and touch functions share some GPIOs. Distinguish nRF52833 application MCU from the USB interface processor. [a]
Sources
Pin and warning references
- micro:bit power supplyPower supply · V2 regulator and current available to the edge connector
- BBC micro:bit V2 Schematic · PDF p. 2Sheet 2/3 · connectors RING0–2, 3V, GND and edge contacts P3–P16, P19, P20
- micro:bit edge connector and pinoutPins and signals · V2 table · physical strip order, MCU pins and pull resistors
- micro:bit I2C busI2C bus · V2 separates internal (sensor) and external (edge connector) buses
Technical sources (3)
- micro:bit v2.0 hardwareMicro:bit Educational Foundation · nRF52 application processor and hardware description
- BBC micro:bit V2 SchematicMicro:bit Educational Foundation · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- New BBC micro:bit announcedMicro:bit Educational Foundation · Announcement 13 October; availability November 2020
Locked source documents
- BBC micro:bit V2 SchematicMicro:bit Educational Foundation · V2.0.0_S · 2020-09-02 · 17aae03003b4fd3686d18aca5ad175c420d29a20
- micro:bit edge connector and pinoutMicro:bit Educational Foundation · microbit-foundation/dev-docs · 469ea5f9faa31989fdb296e726ca24fd558931f4
- micro:bit power supplyMicro:bit Educational Foundation · microbit-foundation/dev-docs · 469ea5f9faa31989fdb296e726ca24fd558931f4
- micro:bit I2C busMicro:bit Educational Foundation · microbit-foundation/dev-docs · 469ea5f9faa31989fdb296e726ca24fd558931f4