Development boards
BeagleBone Black pinout
TI AM3358 · 1 GHz · 3.3 V I/O
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
Ethernet and DC jack at top. Two 46-pin P8 and P9 expansion headers; 67 GPIO-capable 3.3 V contacts (30 of them used by the on-board eMMC/HDMI by default; P9.41 and P9.42 each tie two processor balls) and 7 analog inputs (AIN0–AIN6). TI AM3358 1 GHz Cortex-A8 and dual 200 MHz PRU cores. CAUTION: Analog inputs (AIN) are 1.8 V maximum! Voltages above 1.8 V destroy the ADC. Digital pins are 3.3 V only and not 5 V tolerant.
At a glance
- Platform / manufacturer
- BeagleBoard
- Type
- Development boards
- MCU
- AM3358
- Physical contacts
- 92
- GPIO
- 67
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (8) · SPI (11) · UART (19) · CAN (4) · ADC (7) · PWM (40) · AUDIO (18) · GPMC (51) · IRQ (67) · LCD (29) · MMC (33) · PRU (27) · SYSTEM (67) · TIMER (7)
- Documented by this date
- 2013 [c]
- MCU / processor core
- Arm Cortex-A8 + 2 × PRU [a]
- Clock speed / maximum
- 1 GHz [a]
- Internal RAM / system RAM
- 512 MB DDR3L [a]
- Program Flash / storage
- Rev C: 4 GB eMMC; older revisions 2 GB; microSD [a]
- Pin sources checked
- 2026-11-15
- Technical details reviewed
- 2026-11-14
Cautions for this board
- Do not apply voltage to any I/O pin while the board is unpowered, and drive no pin until SYS_RESETn has gone high (the VDD_3V3B rail is up); otherwise the processor is damaged. Header signals are 3.3 V: 5 V logic levels damage the board. Source: [1] [2]
- Of the 67 GPIO-capable header contacts, 30 are used by on-board devices by default: P8.3–6 and P8.20–25 by the eMMC, P8.27–46 by the HDMI framer. Source: [3] [4]
All pins (92)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| P8.1 | GND | Ground | — | — | [5] |
| P8.2 | GND | Ground | — | — | [5] |
| P8.3 | GPIO1_6MCU pin R9 | General-purpose I/O | gpmc_ad6 (Mode 0) Mode 0mmc1_dat6 (Mode 1) Mode 1gpio1[6] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.4 | GPIO1_7MCU pin T9 | General-purpose I/O | gpmc_ad7 (Mode 0) Mode 0mmc1_dat7 (Mode 1) Mode 1gpio1[7] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.5 | GPIO1_2MCU pin R8 | General-purpose I/O | gpmc_ad2 (Mode 0) Mode 0mmc1_dat2 (Mode 1) Mode 1gpio1[2] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.6 | GPIO1_3MCU pin T8 | General-purpose I/O | gpmc_ad3 (Mode 0) Mode 0mmc1_dat3 (Mode 1) Mode 1gpio1[3] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.7 | TIMER4MCU pin R7 | General-purpose I/O | gpmc_advn_ale (Mode 0) Mode 0timer4 (Mode 2) Mode 2gpio2[2] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.8 | TIMER7MCU pin T7 | General-purpose I/O | gpmc_oen_ren (Mode 0) Mode 0timer7 (Mode 2) Mode 2gpio2[3] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.9 | TIMER5MCU pin T6 | General-purpose I/O | gpmc_be0n_cle (Mode 0) Mode 0timer5 (Mode 2) Mode 2gpio2[5] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.10 | TIMER6MCU pin U6 | General-purpose I/O | gpmc_wen (Mode 0) Mode 0timer6 (Mode 2) Mode 2gpio2[4] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.11 | GPIO1_13MCU pin R12 | General-purpose I/O | gpmc_ad13 (Mode 0) Mode 0lcd_data18 (Mode 1) Mode 1mmc1_dat5 (Mode 2) Mode 2mmc2_dat1 (Mode 3) Mode 3eQEP2B_in (Mode 4) Mode 4pr1_pru0_pru_r30_15 (Mode 6) Mode 6gpio1[13] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.12 | GPIO1_12MCU pin T12 | General-purpose I/O | gpmc_ad12 (Mode 0) Mode 0lcd_data19 (Mode 1) Mode 1mmc1_dat4 (Mode 2) Mode 2mmc2_dat0 (Mode 3) Mode 3eQEP2a_in (Mode 4) Mode 4pr1_pru0_pru_r30_14 (Mode 6) Mode 6gpio1[12] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.13 | EHRPWM2BMCU pin T10 | General-purpose I/O | gpmc_ad9 (Mode 0) Mode 0lcd_data22 (Mode 1) Mode 1mmc1_dat1 (Mode 2) Mode 2mmc2_dat5 (Mode 3) Mode 3ehrpwm2B (Mode 4) Mode 4gpio0[23] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.14 | GPIO0_26MCU pin T11 | General-purpose I/O | gpmc_ad10 (Mode 0) Mode 0lcd_data21 (Mode 1) Mode 1mmc1_dat2 (Mode 2) Mode 2mmc2_dat6 (Mode 3) Mode 3ehrpwm2_tripzone_input (Mode 4) Mode 4gpio0[26] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P8.15 | GPIO1_15MCU pin U13 | General-purpose I/O | gpmc_ad15 (Mode 0) Mode 0lcd_data16 (Mode 1) Mode 1mmc1_dat7 (Mode 2) Mode 2mmc2_dat3 (Mode 3) Mode 3eQEP2_strobe (Mode 4) Mode 4pr1_pru0_pru_r31_15 (Mode 6) Mode 6gpio1[15] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.16 | GPIO1_14MCU pin V13 | General-purpose I/O | gpmc_ad14 (Mode 0) Mode 0lcd_data17 (Mode 1) Mode 1mmc1_dat6 (Mode 2) Mode 2mmc2_dat2 (Mode 3) Mode 3eQEP2_index (Mode 4) Mode 4pr1_pru0_pru_r31_14 (Mode 6) Mode 6gpio1[14] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.17 | GPIO0_27MCU pin U12 | General-purpose I/O | gpmc_ad11 (Mode 0) Mode 0lcd_data20 (Mode 1) Mode 1mmc1_dat3 (Mode 2) Mode 2mmc2_dat7 (Mode 3) Mode 3ehrpwm0_synco (Mode 4) Mode 4gpio0[27] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.18 | GPIO2_1MCU pin V12 | General-purpose I/O | gpmc_clk_mux0 (Mode 0) Mode 0lcd_memory_clk (Mode 1) Mode 1gpmc_wait1 (Mode 2) Mode 2mmc2_clk (Mode 3) Mode 3mcasp0_fsr (Mode 6) Mode 6gpio2[1] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.19 | EHRPWM2AMCU pin U10 | General-purpose I/O | gpmc_ad8 (Mode 0) Mode 0lcd_data23 (Mode 1) Mode 1mmc1_dat0 (Mode 2) Mode 2mmc2_dat4 (Mode 3) Mode 3ehrpwm2A (Mode 4) Mode 4gpio0[22] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.20 | GPIO1_31MCU pin V9 | General-purpose I/O | gpmc_csn2 (Mode 0) Mode 0gpmc_be1n (Mode 1) Mode 1mmc1_cmd (Mode 2) Mode 2pr1_pru1_pru_r30_13 (Mode 5) Mode 5pr1_pru1_pru_r31_13 (Mode 6) Mode 6gpio1[31] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.21 | GPIO1_30MCU pin U9 | General-purpose I/O | gpmc_csn1 (Mode 0) Mode 0gpmc_clk (Mode 1) Mode 1mmc1_clk (Mode 2) Mode 2pr1_pru1_pru_r30_12 (Mode 5) Mode 5pr1_pru1_pru_r31_12 (Mode 6) Mode 6gpio1[30] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.22 | GPIO1_5MCU pin V8 | General-purpose I/O | gpmc_ad5 (Mode 0) Mode 0mmc1_dat5 (Mode 1) Mode 1gpio1[5] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.23 | GPIO1_4MCU pin U8 | General-purpose I/O | gpmc_ad4 (Mode 0) Mode 0mmc1_dat4 (Mode 1) Mode 1gpio1[4] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.24 | GPIO1_1MCU pin V7 | General-purpose I/O | gpmc_ad1 (Mode 0) Mode 0mmc1_dat1 (Mode 1) Mode 1gpio1[1] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.25 | GPIO1_0MCU pin U7 | General-purpose I/O | gpmc_ad0 (Mode 0) Mode 0mmc1_dat0 (Mode 1) Mode 1gpio1[0] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board eMMC (MMC1), which is enabled by default. The eMMC loads these lines and is itself an input/output device: to use the pin for anything else you must boot from microSD and put the eMMC into reset first; do not drive the line before software has done so. Source: [4] | [5] [4] [1] |
| P8.26 | GPIO1_29MCU pin V6 | General-purpose I/O | gpmc_csn0 (Mode 0) Mode 0gpio1[29] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P8.27 | GPIO2_22MCU pin U5 | General-purpose I/O | lcd_vsync (Mode 0) Mode 0gpmc_a8 (Mode 1) Mode 1pr1_pru1_pru_r30_8 (Mode 5) Mode 5pr1_pru1_pru_r31_8 (Mode 6) Mode 6gpio2[22] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.28 | GPIO2_24MCU pin V5 | General-purpose I/O | lcd_pclk (Mode 0) Mode 0gpmc_a10 (Mode 1) Mode 1pr1_pru1_pru_r30_10 (Mode 5) Mode 5pr1_pru1_pru_r31_10 (Mode 6) Mode 6gpio2[24] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.29 | GPIO2_23MCU pin R5 | General-purpose I/O | lcd_hsync (Mode 0) Mode 0gpmc_a9 (Mode 1) Mode 1pr1_pru1_pru_r30_9 (Mode 5) Mode 5pr1_pru1_pru_r31_9 (Mode 6) Mode 6gpio2[23] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.30 | GPIO2_25MCU pin R6 | General-purpose I/O | lcd_ac_bias_en (Mode 0) Mode 0gpmc_a11 (Mode 1) Mode 1gpio2[25] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.31 | UART5_CTSNMCU pin V4 | General-purpose I/O | lcd_data14 (Mode 0) Mode 0gpmc_a18 (Mode 1) Mode 1eQEP1_index (Mode 2) Mode 2mcasp0_axr1 (Mode 3) Mode 3uart5_rxd (Mode 4) Mode 4uart5_ctsn (Mode 6) Mode 6gpio0[10] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.32 | UART5_RTSNMCU pin T5 | General-purpose I/O | lcd_data15 (Mode 0) Mode 0gpmc_a19 (Mode 1) Mode 1eQEP1_strobe (Mode 2) Mode 2mcasp0_ahclkx (Mode 3) Mode 3mcasp0_axr3 (Mode 4) Mode 4uart5_rtsn (Mode 6) Mode 6gpio0[11] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.33 | UART4_RTSNMCU pin V3 | General-purpose I/O | lcd_data13 (Mode 0) Mode 0gpmc_a17 (Mode 1) Mode 1eQEP1B_in (Mode 2) Mode 2mcasp0_fsr (Mode 3) Mode 3mcasp0_axr3 (Mode 4) Mode 4uart4_rtsn (Mode 6) Mode 6gpio0[9] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.34 | UART3_RTSNMCU pin U4 | General-purpose I/O | lcd_data11 (Mode 0) Mode 0gpmc_a15 (Mode 1) Mode 1ehrpwm1B (Mode 2) Mode 2mcasp0_ahclkr (Mode 3) Mode 3mcasp0_axr2 (Mode 4) Mode 4uart3_rtsn (Mode 6) Mode 6gpio2[17] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.35 | UART4_CTSNMCU pin V2 | General-purpose I/O | lcd_data12 (Mode 0) Mode 0gpmc_a16 (Mode 1) Mode 1eQEP1A_in (Mode 2) Mode 2mcasp0_aclkr (Mode 3) Mode 3mcasp0_axr2 (Mode 4) Mode 4uart4_ctsn (Mode 6) Mode 6gpio0[8] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.36 | UART3_CTSNMCU pin U3 | General-purpose I/O | lcd_data10 (Mode 0) Mode 0gpmc_a14 (Mode 1) Mode 1ehrpwm1A (Mode 2) Mode 2mcasp0_axr0 (Mode 3) Mode 3uart3_ctsn (Mode 6) Mode 6gpio2[16] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.37 | UART5_TXDMCU pin U1 | General-purpose I/O | lcd_data8 (Mode 0) Mode 0gpmc_a12 (Mode 1) Mode 1ehrpwm1_tripzone_input (Mode 2) Mode 2mcasp0_aclkx (Mode 3) Mode 3uart5_txd (Mode 4) Mode 4uart2_ctsn (Mode 6) Mode 6gpio2[14] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [6] [3] [1] |
| P8.38 | UART5_RXDMCU pin U2 | General-purpose I/O | lcd_data9 (Mode 0) Mode 0gpmc_a13 (Mode 1) Mode 1ehrpwm0_synco (Mode 2) Mode 2mcasp0_fsx (Mode 3) Mode 3uart5_rxd (Mode 4) Mode 4uart2_rtsn (Mode 6) Mode 6gpio2[15] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.39 | GPIO2_12MCU pin T3 | General-purpose I/O | lcd_data6 (Mode 0) Mode 0gpmc_a6 (Mode 1) Mode 1eQEP2_index (Mode 3) Mode 3pr1_pru1_pru_r30_6 (Mode 5) Mode 5pr1_pru1_pru_r31_6 (Mode 6) Mode 6gpio2[12] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.40 | GPIO2_13MCU pin T4 | General-purpose I/O | lcd_data7 (Mode 0) Mode 0gpmc_a7 (Mode 1) Mode 1eQEP2_strobe (Mode 3) Mode 3pr1_edio_data_out7 (Mode 4) Mode 4pr1_pru1_pru_r30_7 (Mode 5) Mode 5pr1_pru1_pru_r31_7 (Mode 6) Mode 6gpio2[13] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.41 | GPIO2_10MCU pin T1 | General-purpose I/O | lcd_data4 (Mode 0) Mode 0gpmc_a4 (Mode 1) Mode 1eQEP2A_in (Mode 3) Mode 3pr1_pru1_pru_r30_4 (Mode 5) Mode 5pr1_pru1_pru_r31_4 (Mode 6) Mode 6gpio2[10] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.42 | GPIO2_11MCU pin T2 | General-purpose I/O | lcd_data5 (Mode 0) Mode 0gpmc_a5 (Mode 1) Mode 1eQEP2B_in (Mode 3) Mode 3pr1_pru1_pru_r30_5 (Mode 5) Mode 5pr1_pru1_pru_r31_5 (Mode 6) Mode 6gpio2[11] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.43 | GPIO2_8MCU pin R3 | General-purpose I/O | lcd_data2 (Mode 0) Mode 0gpmc_a2 (Mode 1) Mode 1ehrpwm2_tripzone_input (Mode 3) Mode 3pr1_pru1_pru_r30_2 (Mode 5) Mode 5pr1_pru1_pru_r31_2 (Mode 6) Mode 6gpio2[8] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [6] [3] [1] |
| P8.44 | GPIO2_9MCU pin R4 | General-purpose I/O | lcd_data3 (Mode 0) Mode 0gpmc_a3 (Mode 1) Mode 1ehrpwm0_synco (Mode 3) Mode 3pr1_pru1_pru_r30_3 (Mode 5) Mode 5pr1_pru1_pru_r31_3 (Mode 6) Mode 6gpio2[9] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.45 | GPIO2_6MCU pin R1 | General-purpose I/O | lcd_data0 (Mode 0) Mode 0gpmc_a0 (Mode 1) Mode 1ehrpwm2A (Mode 3) Mode 3pr1_pru1_pru_r30_0 (Mode 5) Mode 5pr1_pru1_pru_r31_0 (Mode 6) Mode 6gpio2[6] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P8.46 | GPIO2_7MCU pin R2 | General-purpose I/O | lcd_data1 (Mode 0) Mode 0gpmc_a1 (Mode 1) Mode 1ehrpwm2B (Mode 3) Mode 3pr1_pru1_pru_r30_1 (Mode 5) Mode 5pr1_pru1_pru_r31_1 (Mode 6) Mode 6gpio2[7] (Mode 7) Mode 7GPIO interrupt | Wired to the on-board HDMI framer (LCD signals), which is enabled by default. The framer and small filter capacitors load the line; using the pin for another function disables HDMI. These are also the SYSBOOT pins: do not drive them before SYS_RESETn goes high, or the boot order changes. Source: [3] | [5] [3] [1] |
| P9.1 | GND | Ground | — | — | [5] |
| P9.2 | GND | Ground | — | — | [5] |
| P9.3 | DC_3.3V | Power | — | VDD_3V3B: the 3.3 V rail from the on-board LDO (not the power manager) and the main supply for expansion boards. Rated 250 mA per pin. Source: [2] | [5] [2] |
| P9.4 | DC_3.3V | Power | — | VDD_3V3B: the 3.3 V rail from the on-board LDO (not the power manager) and the main supply for expansion boards. Rated 250 mA per pin. Source: [2] | [5] [2] |
| P9.5 | VDD_5V | Power | — | VDD_5V: 5 V rail from the DC jack. Rated 1000 mA per pin. Source: [2] | [5] [2] |
| P9.6 | VDD_5V | Power | — | VDD_5V: 5 V rail from the DC jack. Rated 1000 mA per pin. Source: [2] | [5] [2] |
| P9.7 | SYS_5V | Power | — | SYS_5V: 5 V system power rail. Rated 250 mA per pin. Source: [2] | [5] [2] |
| P9.8 | SYS_5V | Power | — | SYS_5V: 5 V system power rail. Rated 250 mA per pin. Source: [2] | [5] [2] |
| P9.9 | PWR_BUT | System | — | PWR_BUT is a 5 V-level signal, pulled up inside the TPS65217C power manager and activated by pulling it to GND. It is not a 3.3 V logic pin; do not treat it as a 3.3 V GPIO. Source: [1] | [5] [1] |
| P9.10 | SYS_RESETnMCU pin A10 | System | — | — | [5] |
| P9.11 | UART4_RXDMCU pin T17 | General-purpose I/O | gpmc_wait0 (Mode 0) Mode 0gmii2_crs (Mode 1) Mode 1gpmc_csn4 (Mode 2) Mode 2rmii2_crs_dv (Mode 3) Mode 3mmc1_sdcd (Mode 4) Mode 4uart4_rxd_mux2 (Mode 6) Mode 6gpio0[30] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.12 | GPIO1_28MCU pin U18 | General-purpose I/O | gpmc_be1n (Mode 0) Mode 0gmii2_col (Mode 1) Mode 1gpmc_csn6 (Mode 2) Mode 2mmc2_dat3 (Mode 3) Mode 3gpmc_dir (Mode 4) Mode 4mcasp0_aclkr_mux3 (Mode 6) Mode 6gpio1[28] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.13 | UART4_TXDMCU pin U17 | General-purpose I/O | gpmc_wpn (Mode 0) Mode 0gmii2_rxerr (Mode 1) Mode 1gpmc_csn5 (Mode 2) Mode 2rmii2_rxerr (Mode 3) Mode 3mmc2_sdcd (Mode 4) Mode 4uart4_txd_mux2 (Mode 6) Mode 6gpio0[31] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.14 | EHRPWM1AMCU pin U14 | General-purpose I/O | gpmc_a2 (Mode 0) Mode 0gmii2_txd3 (Mode 1) Mode 1rgmii2_td3 (Mode 2) Mode 2mmc2_dat1 (Mode 3) Mode 3gpmc_a18 (Mode 4) Mode 4ehrpwm1A_mux1 (Mode 6) Mode 6gpio1[18] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.15 | GPIO1_16MCU pin R13 | General-purpose I/O | gpmc_a0 (Mode 0) Mode 0gmii2_txen (Mode 1) Mode 1rgmii2_tctl (Mode 2) Mode 2rmii2_txen (Mode 3) Mode 3gpmc_a16 (Mode 4) Mode 4ehrpwm1_tripzone_input (Mode 6) Mode 6gpio1[16] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.16 | EHRPWM1BMCU pin T14 | General-purpose I/O | gpmc_a3 (Mode 0) Mode 0gmii2_txd2 (Mode 1) Mode 1rgmii2_td2 (Mode 2) Mode 2mmc2_dat2 (Mode 3) Mode 3gpmc_a19 (Mode 4) Mode 4ehrpwm1B_mux1 (Mode 6) Mode 6gpio1[19] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.17 | I2C1_SCLMCU pin A16 | General-purpose I/O | spi0_cs0 (Mode 0) Mode 0mmc2_sdwp (Mode 1) Mode 1I2C1_SCL (Mode 2) Mode 2ehrpwm0_synci (Mode 3) Mode 3pr1_uart0_txd (Mode 4) Mode 4gpio0[5] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.18 | I2C1_SDAMCU pin B16 | General-purpose I/O | spi0_d1 (Mode 0) Mode 0mmc1_sdwp (Mode 1) Mode 1I2C1_SDA (Mode 2) Mode 2ehrpwm0_tripzone_input (Mode 3) Mode 3pr1_uart0_rxd (Mode 4) Mode 4gpio0[4] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.19 | I2C2_SCLMCU pin D17 | General-purpose I/O | uart1_rtsn (Mode 0) Mode 0timer5 (Mode 1) Mode 1dcan0_rx (Mode 2) Mode 2I2C2_SCL (Mode 3) Mode 3spi1_cs1 (Mode 4) Mode 4pr1_uart0_rts_n (Mode 5) Mode 5gpio0[13] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.20 | I2C2_SDAMCU pin D18 | General-purpose I/O | uart1_ctsn (Mode 0) Mode 0timer6 (Mode 1) Mode 1dcan0_tx (Mode 2) Mode 2I2C2_SDA (Mode 3) Mode 3spi1_cs0 (Mode 4) Mode 4pr1_uart0_cts_n (Mode 5) Mode 5gpio0[12] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.21 | UART2_TXDMCU pin B17 | General-purpose I/O | spi0_d0 (Mode 0) Mode 0uart2_txd (Mode 1) Mode 1I2C2_SCL (Mode 2) Mode 2ehrpwm0B (Mode 3) Mode 3pr1_uart0_rts_n (Mode 4) Mode 4EMU3_mux1 (Mode 6) Mode 6gpio0[3] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.22 | UART2_RXDMCU pin A17 | General-purpose I/O | spi0_sclk (Mode 0) Mode 0uart2_rxd (Mode 1) Mode 1I2C2_SDA (Mode 2) Mode 2ehrpwm0A (Mode 3) Mode 3pr1_uart0_cts_n (Mode 4) Mode 4EMU2_mux1 (Mode 6) Mode 6gpio0[2] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.23 | GPIO1_17MCU pin V14 | General-purpose I/O | gpmc_a1 (Mode 0) Mode 0gmii2_rxdv (Mode 1) Mode 1rgmii2_rctl (Mode 2) Mode 2mmc2_dat0 (Mode 3) Mode 3gpmc_a17 (Mode 4) Mode 4ehrpwm0_synco (Mode 6) Mode 6gpio1[17] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.24 | UART1_TXDMCU pin D15 | General-purpose I/O | uart1_txd (Mode 0) Mode 0mmc2_sdwp (Mode 1) Mode 1dcan1_rx (Mode 2) Mode 2I2C1_SCL (Mode 3) Mode 3pr1_uart0_txd (Mode 5) Mode 5pr1_pru0_pru_r31_16 (Mode 6) Mode 6gpio0[15] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.25 | GPIO3_21MCU pin A14 | General-purpose I/O | mcasp0_ahclkx (Mode 0) Mode 0eQEP0_strobe (Mode 1) Mode 1mcasp0_axr3 (Mode 2) Mode 2mcasp1_axr1 (Mode 3) Mode 3EMU4_mux2 (Mode 4) Mode 4pr1_pru0_pru_r30_7 (Mode 5) Mode 5pr1_pru0_pru_r31_7 (Mode 6) Mode 6gpio3[21] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.26 | UART1_RXDMCU pin D16 | General-purpose I/O | uart1_rxd (Mode 0) Mode 0mmc1_sdwp (Mode 1) Mode 1dcan1_tx (Mode 2) Mode 2I2C1_SDA (Mode 3) Mode 3pr1_uart0_rxd (Mode 5) Mode 5pr1_pru1_pru_r31_16 (Mode 6) Mode 6gpio0[14] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.27 | GPIO3_19MCU pin C13 | General-purpose I/O | mcasp0_fsr (Mode 0) Mode 0eQEP0B_in (Mode 1) Mode 1mcasp0_axr3 (Mode 2) Mode 2mcasp1_fsx (Mode 3) Mode 3EMU2_mux2 (Mode 4) Mode 4pr1_pru0_pru_r30_5 (Mode 5) Mode 5pr1_pru0_pru_r31_5 (Mode 6) Mode 6gpio3[19] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.28 | SPI1_CS0MCU pin C12 | General-purpose I/O | mcasp0_ahclkr (Mode 0) Mode 0ehrpwm0_synci (Mode 1) Mode 1mcasp0_axr2 (Mode 2) Mode 2spi1_cs0 (Mode 3) Mode 3eCAP2_in_PWM2_out (Mode 4) Mode 4pr1_pru0_pru_r30_3 (Mode 5) Mode 5pr1_pru0_pru_r31_3 (Mode 6) Mode 6gpio3[17] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.29 | SPI1_D0MCU pin B13 | General-purpose I/O | mcasp0_fsx (Mode 0) Mode 0ehrpwm0B (Mode 1) Mode 1spi1_d0 (Mode 3) Mode 3mmc1_sdcd_mux1 (Mode 4) Mode 4pr1_pru0_pru_r30_1 (Mode 5) Mode 5pr1_pru0_pru_r31_1 (Mode 6) Mode 6gpio3[15] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.30 | SPI1_D1MCU pin D12 | General-purpose I/O | mcasp0_axr0 (Mode 0) Mode 0ehrpwm0_tripzone_input (Mode 1) Mode 1spi1_d1 (Mode 3) Mode 3mmc2_sdcd_mux1 (Mode 4) Mode 4pr1_pru0_pru_r30_2 (Mode 5) Mode 5pr1_pru0_pru_r31_2 (Mode 6) Mode 6gpio3[16] (Mode 7) Mode 7GPIO interrupt | — | [5] [6] [1] |
| P9.31 | SPI1_SCLKMCU pin A13 | General-purpose I/O | mcasp0_aclkx (Mode 0) Mode 0ehrpwm0A (Mode 1) Mode 1spi1_sclk (Mode 3) Mode 3mmc0_sdcd_mux1 (Mode 4) Mode 4pr1_pru0_pru_r30_0 (Mode 5) Mode 5pr1_pru0_pru_r31_0 (Mode 6) Mode 6gpio3[14] (Mode 7) Mode 7GPIO interrupt | — | [5] [1] |
| P9.32 | VADC | Power | — | — | [5] |
| P9.33 | AIN4MCU pin C8 | Analog | ADC AIN4 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.34 | AGND | Ground | — | — | [5] |
| P9.35 | AIN6MCU pin A8 | Analog | ADC AIN6 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.36 | AIN5MCU pin B8 | Analog | ADC AIN5 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.37 | AIN2MCU pin B7 | Analog | ADC AIN2 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.38 | AIN3MCU pin A7 | Analog | ADC AIN3 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.39 | AIN0MCU pin B6 | Analog | ADC AIN0 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.40 | AIN1MCU pin C7 | Analog | ADC AIN1 | 1.8 V maximum analog input! CAUTION: Applying voltages above 1.8 V will permanently destroy the ADC subsystem. Use voltage dividers for 3.3 V or 5 V signals. | [5] |
| P9.41 | CLKOUT2MCU pin D14 | General-purpose I/O | xdma_event_intr1 (Mode 0) Mode 0tclkin (Mode 2) Mode 2clkout2 (Mode 3) Mode 3timer7_mux1 (Mode 4) Mode 4pr1_pru0_pru_r31_16 (Mode 5) Mode 5EMU3_mux0 (Mode 6) Mode 6gpio0[20] (Mode 7) Mode 7GPIO interruptmcasp0_axr1 (D13 · Mode 0) D13 · Mode 0eQEP0_index (D13 · Mode 1) D13 · Mode 1mcasp1_axr0 (D13 · Mode 3) D13 · Mode 3emu3 (D13 · Mode 4) D13 · Mode 4pr1_pru0_pru_r30_6 (D13 · Mode 5) D13 · Mode 5pr1_pru0_pru_r31_6 (D13 · Mode 6) D13 · Mode 6gpio3[20] (D13 · Mode 7) D13 · Mode 7GPIO interrupt (D13) | Two AM3358 balls share this contact: D14 (CLKOUT2, gpio0[20]) and D13 (GPIO3_20, gpio3[20], through R221). Use only one of them and set the other to input mode. Source: [1] [6] | [5] [6] [1] |
| P9.42 | GPIO0_7MCU pin C18 | General-purpose I/O | eCAP0_in_PWM0_out (Mode 0) Mode 0uart3_txd (Mode 1) Mode 1spi1_cs1 (Mode 2) Mode 2pr1_ecap0_ecap_capin_apwm_o (Mode 3) Mode 3spi1_sclk (Mode 4) Mode 4mmc0_sdwp (Mode 5) Mode 5xdma_event_intr2 (Mode 6) Mode 6gpio0[7] (Mode 7) Mode 7GPIO interruptmcasp0_aclkr (B12 · Mode 0) B12 · Mode 0eQEP0A_in (B12 · Mode 1) B12 · Mode 1mcasp0_axr2 (B12 · Mode 2) B12 · Mode 2mcasp1_aclkx (B12 · Mode 3) B12 · Mode 3pr1_pru0_pru_r30_4 (B12 · Mode 5) B12 · Mode 5pr1_pru0_pru_r31_4 (B12 · Mode 6) B12 · Mode 6gpio3[18] (B12 · Mode 7) B12 · Mode 7GPIO interrupt (B12) | Two AM3358 balls share this contact: C18 (GPIO0_7, gpio0[7]) and B12 (GPIO3_18, gpio3[18], through R202). Use only one of them and set the other to input mode. Source: [1] [6] | [5] [6] [1] |
| P9.43 | GND | Ground | — | — | [5] |
| P9.44 | GND | Ground | — | — | [5] |
| P9.45 | GND | Ground | — | — | [5] |
| P9.46 | GND | Ground | — | — | [5] |
General usage notes
3.3 V I/O logic level. TI AM3358 pins are NOT 5 V tolerant; voltages above 3.3 V damage the SoC. Pinmux modes (Mode 0–7) are configured via Device Tree overlays. Source: [1]
Model-specific features and connection notes
- P8/P9 pins may be shared with HDMI and eMMC. Device Tree/pinmux configuration is required. Do not apply 3.3 V to analog inputs. [b]
Sources
Pin and warning references
- BeagleBone Black System Reference Manual · Chapter 7 Expansion Headers P8/P9Chapter 7 · Expansion Connectors · NOTE paragraphs and Connector P9 notes
- BeagleBone Black System Reference Manual · Chapter 8 Cape Board SupportChapter 8 · Expansion Board Power · rail table, current per pin and sequencing rules
- BeagleBone Black System Reference Manual · Chapter 8 Cape Board SupportChapter 8 · LCD Pins · Table 15 and usage notes
- BeagleBone Black System Reference Manual · Chapter 8 Cape Board SupportChapter 8 · eMMC Pins · Table 16 and usage notes
- BeagleBone Black System Reference Manual · Chapter 7 Expansion Headers P8/P9BeagleBone Black SRM Chapter 7 · Expansion Headers P8 and P9 Pinout and Mode Muxing
- AM335x Sitara Processors datasheet · PDF p. 19§4.2 · Table 4-2 Pin Attributes (ZCZ package) · ball signal names and GPIO numbers (pp. 19–47)
Technical sources (3)
- BeagleBone Black specificationsBeagleBoard.org · High Level Specification · processor, memory and onboard eMMC
- BeagleBone Black System Reference Manual · Chapter 7 Expansion Headers P8/P9BeagleBoard.org · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- BeagleBone Black document and board historyBeagleBoard.org · A5.1 production document: April 2013; board family, not every later revision
Locked source documents
- BeagleBone Black System Reference Manual · Chapter 7 Expansion Headers P8/P9BeagleBoard.org · Chapter 7 Tables 87-88
- BeagleBone Black System Reference Manual · Chapter 8 Cape Board SupportBeagleBoard.org · Chapter 8 · snapshot reviewed 2026-11-14
- AM335x Sitara Processors datasheetTexas Instruments · SPRS717L · March 2020