Development boards
Adafruit Feather RP2350 with HSTX pinout
RP2350A · HSTX and STEMMA QT
Open in the interactive atlas →See the pin map, choose functions and save a wiring plan.Türkçe
At a glance
- Platform / manufacturer
- Adafruit
- Type
- Development boards
- MCU
- RP2350A
- Physical contacts
- 54
- GPIO
- 29
- I/O voltage
- 3.3 V I/O
- Interfaces (pin count)
- I²C (35) · SPI (35) · UART (35) · USB (35) · ADC (4) · PWM (35) · CLOCK (18) · HSTX (8) · PIO (35) · QMI (3) · SIO (35)
- MCU / processor core
- 2 × Arm Cortex-M33 / 2 × Hazard3 RISC-V [a]
- Clock speed / maximum
- 150 MHz [a]
- Internal RAM / system RAM
- 520 KB SRAM [a]
- Fixed ROM / boot ROM
- 32 KB boot ROM [a]
- Pin sources checked
- 2026-11-19
- Technical details reviewed
- 2026-11-19
Cautions for this board
- RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1]
All pins (54)
| Physical | Pin name | Type | Functions | Notes and warnings | Source |
|---|---|---|---|---|---|
| JP1.16 | RESET | System | — | — | [2] [3] |
| JP1.15 | 3V3 | Power | — | — | [2] [3] |
| JP1.14 | 3V3 | Power | — | — | [2] [3] |
| JP1.13 | GND | Ground | — | — | [2] [3] |
| JP1.12 | A0MCU pin 40 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 TX F11ADC0 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.11 | A1MCU pin 41 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 RX F11ADC1 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.10 | A2MCU pin 42 | General-purpose I/O | SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10ADC2 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.9 | A3MCU pin 43 | General-purpose I/O | SPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10ADC3 | Non-FT ADC/GPIO RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [6] [5] [1] |
| JP1.8 | D24MCU pin 36 | General-purpose I/O | SPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT2 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.7 | D25MCU pin 37 | General-purpose I/O | SPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT3 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.6 | SCKMCU pin 34 | General-purpose I/O | SPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.5 | MOSIMCU pin 35 | General-purpose I/O | SPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB VBUS EN F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.4 | MISOMCU pin 32 | General-purpose I/O | SPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.3 | RXMCU pin 3 | General-purpose I/O | SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACECLK F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.2 | TXMCU pin 2 | General-purpose I/O | SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP1.1 | PCSMCU pin 12 | General-purpose I/O | SPI1 RX F1UART1 TX F2I2C0 SDA F3PWM4 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.1 | BAT | Power | — | — | [2] [3] |
| JP3.2 | EN | System | — | — | [2] [3] |
| JP3.3 | USB | Power | — | — | [2] [3] |
| JP3.4 | D7MCU pin 10 | General-purpose I/O | SPI0 TX F1UART1 RTS F2I2C1 SCL F3PWM3 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.5 | D4MCU pin 7 | General-purpose I/O | SPI0 RX F1UART1 TX F2I2C0 SDA F3PWM2 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA2 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.6 | D11MCU pin 15 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 RX F11 | Conditional 5.5V input · Same electrical signal as CN2.6 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.7 | D10MCU pin 14 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input · Same electrical signal as CN2.5 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.8 | D9MCU pin 13 | General-purpose I/O | SPI1 CSn F1UART1 RX F2I2C0 SCL F3PWM4 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.9 | D6MCU pin 9 | General-purpose I/O | SPI0 SCK F1UART1 CTS F2I2C1 SDA F3PWM3 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART1 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.10 | D5MCU pin 8 | General-purpose I/O | SPI0 CSn F1UART1 RX F2I2C0 SCL F3PWM2 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA3 F9USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.11 | SCLMCU pin 5 | General-purpose I/O | SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input · Same electrical signal as CN2.3, CONN1.4 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| JP3.12 | SDAMCU pin 4 | General-purpose I/O | SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA0 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input · Same electrical signal as CN2.2, CONN1.3 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [3] [4] [5] [1] |
| CN2.1 | 3V3 | Power | — | — | [2] |
| CN2.2 | SDAMCU pin 4 | General-purpose I/O | SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA0 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input · Same electrical signal as JP3.12, CONN1.3 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.3 | SCLMCU pin 5 | General-purpose I/O | SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input · Same electrical signal as JP3.11, CONN1.4 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.4 | GND | Ground | — | — | [2] |
| CN2.5 | D10MCU pin 14 | General-purpose I/O | SPI1 SCK F1UART1 CTS F2I2C1 SDA F3PWM5 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10UART1 TX F11 | Conditional 5.5V input · Same electrical signal as JP3.7 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.6 | D11MCU pin 15 | General-purpose I/O | SPI1 TX F1UART1 RTS F2I2C1 SCL F3PWM5 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10UART1 RX F11 | Conditional 5.5V input · Same electrical signal as JP3.6 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.7 | GND | Ground | — | — | [2] |
| CN2.8 | NC | System | — | Unconnected | [2] |
| CN2.9 | NC | System | — | Unconnected | [2] |
| CN2.10 | GND | Ground | — | — | [2] |
| CN2.11 | D2PMCU pin 16 | General-purpose I/O | HSTX F0SPI1 RX F1UART0 TX F2I2C0 SDA F3PWM6 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN0 F9USB OVCUR DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.12 | D2NMCU pin 17 | General-purpose I/O | HSTX F0SPI1 CSn F1UART0 RX F2I2C0 SCL F3PWM6 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT0 F9USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.13 | GND | Ground | — | — | [2] |
| CN2.14 | CKPMCU pin 18 | General-purpose I/O | HSTX F0SPI1 SCK F1UART0 CTS F2I2C1 SDA F3PWM7 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPIN1 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.15 | CKNMCU pin 19 | General-purpose I/O | HSTX F0SPI1 TX F1UART0 RTS F2I2C1 SCL F3PWM7 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8CLOCK GPOUT1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.16 | GND | Ground | — | — | [2] |
| CN2.17 | D1PMCU pin 27 | General-purpose I/O | HSTX F0SPI0 RX F1UART0 TX F2I2C0 SDA F3PWM0 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS DET F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.18 | D1NMCU pin 28 | General-purpose I/O | HSTX F0SPI0 CSn F1UART0 RX F2I2C0 SCL F3PWM0 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB VBUS EN F10 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.19 | GND | Ground | — | — | [2] |
| CN2.20 | D0PMCU pin 29 | General-purpose I/O | HSTX F0SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8USB OVCUR DET F10UART0 TX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.21 | D0NMCU pin 31 | General-purpose I/O | HSTX F0SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8QMI CS1n F9USB VBUS DET F10UART0 RX F11 | Conditional 5.5V input RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CN2.22 | GND | Ground | — | — | [2] |
| CONN1.1 | GND | Ground | — | — | [2] |
| CONN1.2 | 3V3 | Power | — | — | [2] |
| CONN1.3 | SDAMCU pin 4 | General-purpose I/O | SPI0 SCK F1UART0 CTS F2I2C1 SDA F3PWM1 A F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA0 F9USB VBUS EN F10UART0 TX F11 | Conditional 5.5V input · Same electrical signal as JP3.12, CN2.2 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
| CONN1.4 | SCLMCU pin 5 | General-purpose I/O | SPI0 TX F1UART0 RTS F2I2C1 SCL F3PWM1 B F4SIO F5PIO0 F6PIO1 F7PIO2 F8TRACEDATA1 F9USB OVCUR DET F10UART0 RX F11 | Conditional 5.5V input · Same electrical signal as JP3.11, CN2.3 RP2350-E9 (A2 stepping): a Bank 0 GPIO configured as an input can be held at about 2.2 V by pad leakage while its voltage is in the undefined logic region; the internal pull-down is too weak to overcome it. Pull or drive the line low with 8.2 kΩ or less; the pull-up still works. Source: [1] | [2] [4] [5] [1] |
Model-specific features and connection notes
- Two cores run concurrently; all four cores cannot run together. 12 PIO state machines. [a]
Sources
Pin and warning references
- RP2350 Datasheet · PDF p. 1359Appendix D.5.1 · RP2350-E9 · increased leakage on Bank 0 GPIO inputs (A2 stepping; pp. 1359–1360)
- Adafruit Feather RP2350 Eagle schematicEagle schematic · JP1, JP3, CN2 and CONN1 nets
- Adafruit Feather RP2350 PrettyPins · PDF p. 1Top-view header orientation and factory silkscreen
- RP2350 Datasheet · PDF p. 1333§14.8.2.2 · Tables 1674–1679 · package pin list
- RP2350 Datasheet · PDF p. 1332§14.8.2.1 · Table 1673 · FT input conditions; pin types in Tables 1674–1679
- RP2350 Datasheet · PDF p. 1334§14.8.2.2 · Tables 1674–1679 · package pin list
Technical sources (3)
- RP2350 DatasheetManufacturer · Locked pin-source document; see sources/manifest.json for revision and SHA-256
- Feather RP2350 with HSTX pinoutsAdafruit · Memory and expansion connectors
- Adafruit Feather RP2350 Eagle schematicAdafruit · Locked schematic or pin-source document
Locked source documents
- RP2350 DatasheetRelease 8 · 2026-10-01
- Adafruit Feather RP2350 PrettyPinsAdafruit · d7bc5cb6c16f071e01ae1cf790ee2142d376ee41
- Adafruit Feather RP2350 Eagle schematicAdafruit · d7bc5cb6c16f071e01ae1cf790ee2142d376ee41